Jump to content
SAU Community

Recommended Posts

So i drove from up to Lake Mountain today and took the kids to the snow.

Between Healsville and Marysville i put the stick into Manual and discovered that the transmission would not shift up or down on demand and the display just sat on "4"

In "D" mode it was still working perfectly and shifting automatically. It just would not shift manually.

I pulled over in Marysville and it was working in Manual again. (without even having to re-set the ignition)

I'm thinking it was some kind of safety feature on the transmission computer and perhaps the transmission was getting hot due to all the hill climbing and low gear work.

Down hill all the way home and manual shifts were perfect.

Has anyone else experienced this issue?

Should i get a transmission cooler and if so how much, where from and how to?

Car is an M35 ARX

Cheers in advance and hope to see you all soon on the next cruise.

Chris

Edited by ChrisB
Link to comment
https://www.sau.com.au/forums/topic/403889-do-i-need-a-transmission-cooler/
Share on other sites

Yes, get a trans cooler. Costs about $100 & available from auto stores everywhere & E-bay etc. Simple to fit. Just look first at how much room you have & get one to suit. It doesn't need to be very big to be effective.

Edited by Commsman

I'm getting The same experience Mostly long drives. done the oil tranny change, it helps.

If I get one - I might get one from eBay without the hoses and fittings, might get them from earls just to make sure that I can mount it where suitable

Don't bother with earls fittings and 'performance hose'.... the lines arn't under that much pressure. PWR make some great trans coolers in most usable sizes. They're available from repco etc - the whole lot should come in under $120 including more hose if needed. The PWR kit comes with hose clamps and mounting fittings etc. Make sure you buy trans hose if you need to buy extra.

I'd sugest plumbing it in after the/any factory coolers (not sure on your m35, you may have a small air to air cooler or a warmer/cooler as part of the radiator) and using a cooler core that has slightly larger inlet/outlet fittings than the stock cooler (just reduces any pressure loss across the core).

I'd also change the trans fluid too...

This is what I did with my C34, it works a treat with my modified auto trans.

Cheers

Justin

I learnt the hard way in how valuable an oil cooler is the other day in my Jeep. Going over a big set of hills, just started blowing smoke. Didnt loose any function in the box to begin with. Now it doesnt have 4th and reverse is almost gone. It did something similar to yours about a year back, thought it was a computer problem, swapped it out and didnt have a problem until the gearbox blew its load everywhere.

Guys,

Great Information thanks.

The Transmission was flushed and filled with Mattic S a few months ago.

I will check the colour but hope its OK.

When i get a transmission cooler i hope it will only need topping up.

When plumbing in the cooler, should i put it in series with the radiator or disconnect the trans hoses from the radiator?

I put mine in series with the radiator so that the warm oil flows thru the a/m cooler then onto the radiator. This means the trans should get up to temp quicker as the oil is warmed by the radiator before it flows back in. It also means on really hot days it will take some load off the radiator by cooling the trans fluid a bit before it gets there.

Running it independant of the radiator will work OK as well (no heat load on the radiator at all), but may take a little longer to get up to good operating temp.

I fitted one of these thermostats inline with my trans cooler, it allows the transmission to warm up to operating temp before flowing through the cooler, and will limit the amount of cold 'issues' you will have when you just plumb it in.

http://www.ebay.com.au/itm/LONG-OIL-THERMOSTAT-COLD-CLIMATES-OC-708-4739-/370626344630?pt=Motors_Car_Truck_Parts_Accessories&hash=item564b0d36b6#ht_820wt_1159

The hoses may be a different size, I had to use adapters for the hoses, but it works well.

I put mine in series with the radiator so that the warm oil flows thru the a/m cooler then onto the radiator. This means the trans should get up to temp quicker as the oil is warmed by the radiator before it flows back in. It also means on really hot days it will take some load off the radiator by cooling the trans fluid a bit before it gets there.

Do you remember which hose between the gearbox & radiator was which?

I was planning on hooking up my trans cooler the exact same way...

From memory. If you are lying under the car looking towards the rear.

Top is pressurised flow from the trans, bottom is the return to the trans. That's the hard lines that end just near the sump. To make sure, just pull the bottom line off the hard line, and put it in a clean 1 litre bottle. Get someone to turn the car on for only 2 or 3 seconds. Should pump out 500 ml or so. You can add the fluid back in via the dipstick.

With a NA c34? Towing a rally car? Might be a bit over zealous there.

So 750kg of trailer, and 1200kg of car; how early will you be leaving for an event? Any hills along the way?

Not my pick for a tow car; that's for sure.

With a NA c34? Towing a rally car? Might be a bit over zealous there.

So 750kg of trailer, and 1200kg of car; how early will you be leaving for an event? Any hills along the way?

Not my pick for a tow car; that's for sure.

Ahh you know, figured it weighed in pretty similar to a V6 Holden and the Straight 6 Cherokee it wouldnt be too bad.

And as for time it would be day before and NZ doesnt have many flat roads.

Is more of a long term possibility then needing to go to an event next week.

I still have to rebuild and sell my Cherokee and move to a more car friendly place before I consider it.

Ahh you know, figured it weighed in pretty similar to a V6 Holden and the Straight 6 Cherokee it wouldnt be too bad.

And as for time it would be day before and NZ doesnt have many flat roads.

Is more of a long term possibility then needing to go to an event next week.

I still have to rebuild and sell my Cherokee and move to a more car friendly place before I consider it.

Yeah, weight of the Stagea is probably similar to a V6 Holden; the torque from a NA RB25 however, no where near similar. :no:

You'll be giving the clutch a hiding just to get it moving.

RB25/30 with a turbo? Now you're talking. :whistling:

on the towing note - ive towed a few heavy loads (64 besser bricks + trailer, car trailer + car), and my car(c34 rs4s) tows beautifully, only issue ive had was clutch slippage reversing the car trailer of a steep driveway, only slipped for a second before all 4 wheels started spinning. but definatly wouldnt recommend with an na.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...