Jump to content
SAU Community

Recommended Posts

  • Replies 182
  • Created
  • Last Reply

Top Posters In This Topic

its a freeway dolphin vented bonnet i'll hopefully be making a mould and might sell a few as they are no longer avaliable...........

You bastard! I was looking at them a while ago, hoping they'd make a short run. Figured options these days started and ended with Masa.

Let me know if you start making copies... Very interested.

You bastard! I was looking at them a while ago, hoping they'd make a short run. Figured options these days started and ended with Masa.

Let me know if you start making copies... Very interested.

That's 2! ;)

Out of curiosity whats happening with these rear braces

I spoke to jase the other day...they have finished the order.....we are just waiting for the final delivery inn japan for distribution. As soon as I know more ill post it but it should not be to long from here.

Alrighty...

All 20 rear braces have been sent from Ox to my mate (Apparently Ox did ask the question if front braces would also be required) - I told them no!!

They will be split up into lots according to the states below and sent to the contact point at the top of each state's list:

VICTORIA

prince_skyline (delivery point)

IRONPAW (VIC)

Scotty NM35 (VIC)

SydSyd (VIC)

Ot1 (NZ) - I'll on forward to you in NZ (pm me your address)

NSW

jetwreck (delivery point)

WAGON BOY (NSW)

Mr 20Valve (NSW)

Commsman (NSW)

Howaitonaito (NSW)

Rosella (NSW)

Rudi ARX TURBO (NSW)

Daleo (NSW)

QLD

joshm35 (delivery point)

Dcdc (QLD)

LineitUp (QLD)

R6n350GT (QLD)

SA

bigkevracer (delivery point)

impul535w (SA)

Skipovalov (SA)

We are aiming to have these sent out by Thursday/Friday this week, so if there is any changes required to the above, please let me know ASAP. Craig has provided the delivery point addresses. I will get tracking numbers so they can be tracked and let you know. Should be around a 7 - 10 days delivery to the delivery points..

Edited by prince_skyline

Done - updated list:

VICTORIA - 5 pieces (incl. 1 NZ)

prince_skyline (delivery point)

IRONPAW (VIC)

Scotty NM35 (VIC)

SydSyd (VIC)

Ot1 (NZ) - I'll on forward to you in NZ (pm me your address)

NSW - 7 pieces

jetwreck (delivery point)

WAGON BOY (NSW)

Mr 20Valve (NSW)

Howaitonaito (NSW)

Rosella (NSW)

Rudi ARX TURBO (NSW)

Daleo (NSW)

QLD - 5 pieces

joshm35 (delivery point)

Dcdc (QLD)

LineitUp (QLD)

R6n350GT (QLD)

Commsman (NSW/QLD)

SA - 3 pieces

bigkevracer (delivery point)

impul535w (SA)

Skipovalov (SA)

Cheers

The rear Braces were sent yesterday (small delay as i needed to confirm phone numbers of mail recipients). According to tracking they left Tokyo today.

4 parcels as per the destination points above. ETA is 3-7 days (EMS), so may even receive them by Friday...

Tracking numbers are below:

VICTORIA - 5 pieces (incl. 1 NZ) - TRACKING NUMBER EJ185487589JP

prince_skyline (delivery point)

NSW - 7 pieces - TRACKING NUMBER EJ185487592JP

jetwreck (delivery point)

QLD - 5 pieces - TRACKING NUMBER EJ185487601JP

joshm35 (delivery point)

SA - 3 pieces - TRACKING NUMBER EJ185487615JP

bigkevracer (delivery point)

Track here (RHS of page): http://www.post.japa...s/index_en.html

Edited by prince_skyline

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...