Jump to content
SAU Community

Recommended Posts

Ok so my 32 has a little issue,

This happens In the morning or the evening after the car has sat for a decent amount of time, I don't run the car hard as it is a daily, 45 min drive to work.

Anyway, I get smoke out of the exhaust, it seems to be an oil smoke.

It comes out when I accellarate, but only once....I.e

Accellarate to 3000 rpm, will smoke ...do it again to 3 k...no smoke

Rev further to higher rpm and more smoke after 3krpm, make sense?

It seems to clear it out, like clearing your throat.

I always warm the car up never drive cold.

My thoughts were theirs oil draining/ seeping somewhere it shouldn't and being sucked back into the engine when I go again later on.

One it's cleared theirs no more smoke

What should I be checking here?

I do know from a service report that my turbo oil drain line had a slight weep, any link here do you think?

Edited by GH05T
Link to comment
https://www.sau.com.au/forums/topic/406304-smoke-in-the-morning/
Share on other sites

Possibly valve stem seals. Car sits and a small amount of oil weeps past the seal. Start car, give it a squirt and the oil burns off.

Give it a comp test and if it comes up chipper, then it's likely the valve stem seals as they won't generally, affect your compression. If comp is down then you have a bigger problem.

Then I'd say almost defo valve stem seals.

If it is valve stem seals I wouldn't be too concerned. Just make sure you keep an eye on your oil level and if it gets worse, like blowing smoke under power and or a lot of of smoke on start up, then it's time to look at getting your head refreshed.

That puff of smoke on cold takeoff is usually condensate oil from the PCV running down into the manifold overnight. You can try fitting a small sealed catch can full of stainless steel wool in the pcv hose to prove it.

That's what it seems like, from a stand still any acceleration gives a noticeable amount of blue smoke (visage at night in headlights behind) and like I said its like it puffs as far as it revs, but only once, accel to 2000rp with smoke but only once, more smoke when you go past that rpm again,

Is this problem going to get worse if the car gets driven hard? I drive daily and maby one in a while it gets a caining, should I be carefull, is their anything I can spenda bit of coin n to help further expenses ?

I always warm the car up never drive cold.

Drive it cold (but sensibly!). Most of the damage is done when the engine is cold. It will warm up much quicker than simply letting it idle.

And you won't be coming back later asking why your fuel economy is so crap.

dont care at all about fuel i dont pay for it, i run my car for 15 mins in the morning before driving, i run it for about 3-5 in the evening after work, nether affect the smoke though, its always the same

Blind_elk is right. Warming up vehicles, especially ones that rev, is a very bad idea. Generally at idle the oil pump isn't pushing a great deal of oil around and there's not much temp increase which means it takes longer to get oil everywhere and also up to temp.

Start car, let idle for 30 seconds then get driving.

Idling a cold car for 15 minutes is a great way to destroy rings and valve stem seals.

Yeah idling for 15 minutes is not a good idea at all, would barely warm it up, would get up to temp in 1-2 minutes of normal driving otherwise. Start it, wait 30 seconds then drive off staying off boost until temp is up.

Smoke could be turbo seal or valve stem seals.

Edited by Rolls

Valve stem seals means head off. In reality leaky valve stem seals won't do any damage (at least in your case as it seems not too bad.. They'll just progressively get worse until such time as it smokes a lot more or all the time and then it needs to be fixed.

I'm not sure how hard it is to get the head off an RB as I've not done one, but once off, barring any weird RB specific oddity, the seals might be maybe $100 or so and the work to actually fit them might be 4 hours (that's a pretty rough guesstimate). Of course, if it were me, with the head off and the valve train off it would be hard to resist giving the head a through going over.

As for turbo seals, that's a tougher one. That means turbo off and either a "back to stock" rebuild for $500+ or replace with something tastier for $1000+ plus required supporting mods.

TBH it sounds to me more like valve stem seals rather than turbo. I think if it was the turbo it would produce more smoke under load.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...