Jump to content
SAU Community

Recommended Posts

Ok so my 32 has a little issue,

This happens In the morning or the evening after the car has sat for a decent amount of time, I don't run the car hard as it is a daily, 45 min drive to work.

Anyway, I get smoke out of the exhaust, it seems to be an oil smoke.

It comes out when I accellarate, but only once....I.e

Accellarate to 3000 rpm, will smoke ...do it again to 3 k...no smoke

Rev further to higher rpm and more smoke after 3krpm, make sense?

It seems to clear it out, like clearing your throat.

I always warm the car up never drive cold.

My thoughts were theirs oil draining/ seeping somewhere it shouldn't and being sucked back into the engine when I go again later on.

One it's cleared theirs no more smoke

What should I be checking here?

I do know from a service report that my turbo oil drain line had a slight weep, any link here do you think?

Edited by GH05T
Link to comment
https://www.sau.com.au/forums/topic/406304-smoke-in-the-morning/
Share on other sites

Possibly valve stem seals. Car sits and a small amount of oil weeps past the seal. Start car, give it a squirt and the oil burns off.

Give it a comp test and if it comes up chipper, then it's likely the valve stem seals as they won't generally, affect your compression. If comp is down then you have a bigger problem.

Then I'd say almost defo valve stem seals.

If it is valve stem seals I wouldn't be too concerned. Just make sure you keep an eye on your oil level and if it gets worse, like blowing smoke under power and or a lot of of smoke on start up, then it's time to look at getting your head refreshed.

That puff of smoke on cold takeoff is usually condensate oil from the PCV running down into the manifold overnight. You can try fitting a small sealed catch can full of stainless steel wool in the pcv hose to prove it.

That's what it seems like, from a stand still any acceleration gives a noticeable amount of blue smoke (visage at night in headlights behind) and like I said its like it puffs as far as it revs, but only once, accel to 2000rp with smoke but only once, more smoke when you go past that rpm again,

Is this problem going to get worse if the car gets driven hard? I drive daily and maby one in a while it gets a caining, should I be carefull, is their anything I can spenda bit of coin n to help further expenses ?

I always warm the car up never drive cold.

Drive it cold (but sensibly!). Most of the damage is done when the engine is cold. It will warm up much quicker than simply letting it idle.

And you won't be coming back later asking why your fuel economy is so crap.

dont care at all about fuel i dont pay for it, i run my car for 15 mins in the morning before driving, i run it for about 3-5 in the evening after work, nether affect the smoke though, its always the same

Blind_elk is right. Warming up vehicles, especially ones that rev, is a very bad idea. Generally at idle the oil pump isn't pushing a great deal of oil around and there's not much temp increase which means it takes longer to get oil everywhere and also up to temp.

Start car, let idle for 30 seconds then get driving.

Idling a cold car for 15 minutes is a great way to destroy rings and valve stem seals.

Yeah idling for 15 minutes is not a good idea at all, would barely warm it up, would get up to temp in 1-2 minutes of normal driving otherwise. Start it, wait 30 seconds then drive off staying off boost until temp is up.

Smoke could be turbo seal or valve stem seals.

Edited by Rolls

Valve stem seals means head off. In reality leaky valve stem seals won't do any damage (at least in your case as it seems not too bad.. They'll just progressively get worse until such time as it smokes a lot more or all the time and then it needs to be fixed.

I'm not sure how hard it is to get the head off an RB as I've not done one, but once off, barring any weird RB specific oddity, the seals might be maybe $100 or so and the work to actually fit them might be 4 hours (that's a pretty rough guesstimate). Of course, if it were me, with the head off and the valve train off it would be hard to resist giving the head a through going over.

As for turbo seals, that's a tougher one. That means turbo off and either a "back to stock" rebuild for $500+ or replace with something tastier for $1000+ plus required supporting mods.

TBH it sounds to me more like valve stem seals rather than turbo. I think if it was the turbo it would produce more smoke under load.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...