Jump to content
SAU Community

Recommended Posts

I tend to leave from Northcote at 5:45am, though I don't stop on the way. Note I don't go through Cranbourne either - I head towards Pakenham on the Freeway and cut down Koo Wee Rup Road.

Went down to Chasers to have the engine checked out, don't know if the other garage's instrument read low last time but compression was again even but up at around 160 per cylinder, leak down test was also very good. Looks like I can continue to target my money at the rear suspension and possibly Paul Ruzic EM Pro to provide engine monitoring to keep it so - currently just have standard dash.

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

good news on the comp test, just keep it cool and fill it with fresh oil frequently and bobs your uncle!

i'd love to throw some money at the rear end in my car, it's a constant struggle trying to keep it straight.

have fun at the island!

putting 300kw through my stock rear end was a nightmare at Sandown I just couldnt get on it anywhere but the straights, even then it was point and shoot but dont pull the trigger to hard

...wasnt too bad at PI though, just drove like a normal car but faster,only on the tight tight handers it wanted to step out :D

1.5Way KAAZ or NISMO diff is a must. it's $1500 worth of kit, but money well spent.

This is what Birds was telling me.

How much of a difference did you notice? Just traction out of corners or....?

Yeah diff and brakes is the last big spend I have really..It will have to wait though so in the meantime I will just cruise around and learn the road..

And swaybars..mind of I ask what sizes you run John or is it secret squirrel business..

Adjustable Whiteline Front, there is only one size 24mm.

Fixed Whitline Rear, 20mm.

The diff changes the way the car behaves, not only under power but off power into corners. It's less sloppy and more direct, the change on the road is equally as good. Rob in the black 33 just changed from the stock diff to a KAAZ 1.5 way recently.

GTR is different. The GTR rear subframe is different so is the front (obvious reasons there, front diff)

27mm for the front of the ECR33 is fixed mate. That would be terrible, unless you like massive understeer all the time.

My entry was confirmed by email yesterday too, as scrutiny opens at 7:30 I guess we would need to be there around that time, especially with up to 140 entrants.

I will be meeting other drivers at McDonalds Cranbourne at 6am if you want to get a quick bite and head down with us.

cool, i'll try to make it by then however i'll probably be running late and miss you guys.

What a gorgeous day, looking forward to tomorrow. Where are you planning to park up, if early, close to cafe or at far end of garages near the garage used as the entrance to pit lane?

^^ Was pushed up beside the scrutineering shed, didn't look good.

Pretty happy with my new PB of 1:56, not bad for a 2 ton car I thought. lol.

My gearbox let me down again, perhaps time for a manual conversion?

post-63525-0-05824600-1346638290_thumb.jpg

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...