Jump to content
SAU Community

Recommended Posts

The builder of my engine has set a minimum idle rpm to a little over 2000 when the car warms up, which usually takes about 10 minutes until it drops down to normal idle and is completely warmed up.

Until a few days ago I've had no problems with this, but lately I've been hearing more and more about how it's bad to let the car warm up by just idling and the better alternative is slowly driving it till it's warmed up.

So my question is would it be alright if I just let it warm up the way I have been, by letting it idle until the revs go down to normal like it has been tuned ? Or just start driving but at low rpm ?

Sorry if this is in the wrong section !

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/409379-warming-up-with-forged-pistons/
Share on other sites

To expand a little on why warming up on idle is bad, at idle (even 2000rpm) your oil pump isn't moving a lot of oil meaning poor supply to the top of the engine which in turn leads to poor oil circulation to everything else which in turn leads to increased wear.

It's actually because at idle the rings aren't sealing very well compared to driving with a bit of load, so fuel can get past and contaminate the oil, and on new engines It will glaze the bores too.

Not to mention it takes 5 times longer to get to temp by idling.

I don't think it takes too long for most engines to get the chill out of their pistons , pistons don't have a real lot of thermal mass and being aluminium means they absorb combustion heat pretty quickly . Obviously the most important thing at start up is getting oil circulating everywhere and good oils lubricate pretty well even when cold . I reckon somewhere between the oil flowing properly from cold and everything expanding as it heats up uniformy enough are the important factors here .

Running an engine fast from cold is obviously intended to generate enough extra heat to warm an engine up faster than it would just idling at say 9-1200 revs . The only logic I can see in this is performance if you want to drive it hard from the first turn of the wheels . As was mentioned things like gearboxes and diffs don't heat their fluids standing still .

The thing to remember is that most current production cars are pretty well sorted nowdays and they start and run well . Many cars that have been played with particularly engine management wise don't run so well from cold start and can have all sorts of drivability issues . I'd say because they don't run perfectly when cold is part of the reason many petrol heads like to warm them up a bit before driving away .

Anyway everyone has their own ideas but I think everyone feels better when the temp gauge climbs off its peg .

IMO oil circulation is no 1 priority and what you do just after your engine fires up should probably take oil formulation and viscosity into account . Heavy grade oils won't heat or become more "fluid" as quickly as lighter grade ones so if using say a 10W60 you may need to soft pedal a bit longer than if you were using something like a 0 or 10W40 .

Some engines take longer to warm up than others and if yours is like this I suggest you check and renew your coolant thermostat , I also resist the temptation to run cooler than std thermostats because a cooler running engine takes longer to get its oil up to temp . To me 76C is fine .

There may be some cold start tuning strategies that help an engine generate a bit extra heat to warm up quickly , if anyone knows of any I'm all ears .

A .

when the engines cold i dont think driving off straight away makes sense, piston to bore clearance is at its greatest, turbo and top end maybe thin films,

so i wait till i see 50degrees on the power fc takes about 5 mins, probably takes about 25mins before any big boost..

a warm up is like foreplay, it gets her well lubed before the action. :yes:

Edited by SliverS2

So, you would rather sit there idling, wasting fuel, for 5 minutes with a large piston - bore clearance, than drive for 2 minutes with a large piston - bore clearance after which the engine will be at 50, and you will be 2 minutes closer to you destination.

The harder the engine works, the more heat it produces. The more heat it produces, the faster it gets to the correct operating temperature (which should be as the manufacturer designed it to be, so don't go installing "cooler" thermostats). The maximum wear rate in an engine is during the warm-up period. Taxi engines basically last for ever, because they rarely get cold.

Any good engineer, with the exception of Adam Gilchrist's father, will tell you to drive from the get-go. Trying to get the engine warm by idling is a waste of fuel (and therefore money).

i doubt id waste much fuel, id rather look after the motor than have it operating under load when its stone cold..

Im never in a rush with my engine cold, why is there so much concern over a short idle time, are you that short of a dollar? The issue is not wasting a dollar here or there on fuel , its the longevity of the motor. After spending a few thousand dollars on a brand new turbo, im not going to take off at the turn of a key.

My brother did that in his rotary he had and it blew some seals somwhere, turnt into a smoker.. so in that case it did need warm up time.

i take 5mins just to get out the front gate, theres a notable difference after 5mins, the motor is free'd up a bit rather than cold and groggy..

Edited by SliverS2

i doubt id waste much fuel, id rather look after the motor than have it operating under load when its stone cold..

Im never in a rush with my engine cold, why is there so much concern over a short idle time, are you that short of a dollar? The issue is not wasting a dollar here or there on fuel , its the longevity of the motor. After spending a few thousand dollars on a brand new turbo, im not going to take off at the turn of a key.

My brother did that in his rotary he had and it blew some seals somwhere, turnt into a smoker.. so in that case it did need warm up time.

i take 5mins just to get out the front gate, theres a notable difference after 5mins, the motor is free'd up a bit rather than cold and groggy..

cant compare a rotary engine to a skyline engine, rotarys are fragile at best and intolerant of detonation, with the engine running/idling you will get a SMALL amount of heat getting blown onto the gearbox via the engine fan

^^^ rotaries always blow seals, nothing to do with warm up :whistling:

It's not about money why people do it. Idling at 2-3% load compared to driving it at 10% load can more than halve warm up period.

Even heavy truck engines alternate cylinders so only half are firing to load up and warm the engine faster

There may be some cold start tuning strategies that help an engine generate a bit extra heat to warm up quickly , if anyone knows of any I'm all ears .

By the time I've got the car out onto the road it has been idleing for a few minutes and I take it easy till the first hill when I drag the brakes and load the motor up slightly to zero on the boost gauge. By the time I'm at the top of the hill temp gauge has moved up to close to normal

EDIT

Same with the truck I drive

If I let it idle it takes a good 10 mins to even move the gauge but if I let it idle while I sort the paperwork pump up air etc then leave the yard and cruise up the hill it is up to a quarter on the gauge and off the fast idle

Edited by m.j.h

i dont think the guage is a very good indicator, when the power fc gives 50degrees, the needle is still under the line

^^^ rotaries always blow seals, nothing to do with warm up :whistling:

It's not about money why people do it. Idling at 2-3% load compared to driving it at 10% load can more than halve warm up period.

Even heavy truck engines alternate cylinders so only half are firing to load up and warm the engine faster

its a personal thing, to me its zero load for 3-5mins to let the parts expand and lube up, 50deg is better than 10deg and drive off.. my opinon only..

I subscribe to both ideas. I start the car and push it out of its spot (to make getting to the passenger door easier to put my laptop bag, lunch, etc in) then go back inside to say goodbye to everyone. The car gets a couple of minutes of idling so that I don't have to drive it up my 45° driveway* and 35° residential street** dead cold. It absolutely goes up those hills better if it is let run for a couple of minutes than if thrown at them cold. And there is no way to avoid making boost up the driveway even in first, and the street can oonly be done if willing to drive at 10km/h the whole way up.

There are reasons for everything.

* exageration, yes, but it is bloody steep.

** also exageration.

Edited by GTSBoy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...