Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

mofos at tirerack won't ship yoko's or hankooks. Dunlop it is!

The last quote I got for the Dunlop Direzza Z1 Star specs in Australia was between $360 and $400 a tyre if I remember correctly.

Tire rack had them at the time for $128 a tyre.

Add the $350 shipping and I was still miles ahead in savings.

Things may have changed though.

Not yet. It's $1185 landed from Tirerack for the set. Are they a much better tyre than say Federal RS-R's?

I believe the Federals are a UTQG 140 where as the Dunlops are 200, Ive never used Federals myself so I cannot compare.

The Hankooks are 140 and I found the Hankooks wear more than the Dunlops but the Hankooks are more grippy straight off where the Dunlops needed a lap to come good and did get a bit "greasy" after about 8 laps at Wakie.

Disclaimer: Im far from a expert in these things.

Thats a bugger though about not shipping the Hankooks, I myself may go back to the Star Specs.

  • 3 weeks later...

the add mentioned above is listed by me

the ad08's are excellent and worth every cent

was running these on my 300kw+ r32 gtr and the grip and handling exceptional

reason y i am not running them as i have gone to 355 disks and need to run 18's

Just ordered x4 Nitto NT555's in 255 40 17 for $125ea in free delivery. 3 hours left for the sale at time of writing. Not sure how good they are but should be OK for 2nd set of rims.

http://www.ozzytyres.com.au/store/nitto-255-40r17-94w-nt555.html

  • 3 months later...

ES501's are a "Comfort" "silent" type tyre for people who value things like fuel economy.

Toyo Proxes4 seem like more of a performance tyre so should be comparable to Fed595, possibly better. For $170 they seem like worth trying.

Do a search on here, you should find plenty of good info.

Proxes 4 are not a UHP tyre in the way that the KU36 and 595s are. They are a good tyre, but they are nowhere near as soft in the compound. They have a treadwear rating of 300 vs the <200 numbers on most of the other tyres being discussed. That puts them in the same company as the FK452 and so on.

I've used both the Proxes 4 and FK452 on my R32 many years ago and the KU36s were like chalk and cheese in terms of sheer grip. I used to get up to 20k km out of FK452. Only get about 10k km out of KU36. They are in a different world.

Dunno what the nitto invos are worth in a 17 but they are a great street tyre loads of grip and VERY quiet. If you did get 595's make sure you get the Z soft compound 1's think the tread wear is 220 cos the taxi spec hard compound 1's are crap!

I've used Toyo Proxes 4 and find them some what similar in performance to a cheaper Kumho KU31 (half the price of the Toyos).

Mick, I jelly it says you haz Evo 9 :)

Haha yeah Johnny its such a blast to drive! Not near as quick as my 33 BUT I'm working on that :) the evo has Dunlop SP maxx tyres on it and they are quite a good tyre I've found. Bit noisier than the invos but they are quite good in the wet and the dry.

I've driven a few of EVOs my mates own.. they're fun to drive, but you do miss the fighting nature of the car (that being an uncontrollable RWD) :)

You'll probably leave SAU and only be on OzEvo all day long

Yeah i will see how the evo feels when i wind it up to 300+kw like i did with the skyline lol :woot:

But no never the SAU community is far better than the evo crowd :whistling:

I've driven a few of EVOs my mates own.. they're fun to drive, but you do miss the fighting nature of the car (that being an uncontrollable RWD) :)

You'll probably leave SAU and only be on OzEvo all day long

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...