Jump to content
SAU Community

Recommended Posts

I have been testing a few of my bypass kits out on my car, Cam's PM35 and a turbo V35, all showing good results. Hopefully Cam can add his logging data to the thread later.

It consists essentially of a hose connecting the block to the coolant return line back to the radiator via the heater hose. I decided to fix the air bleeding issue at the same time, with a ball valve for easy filling and purging. I was hoping to make up some funnels to screw into the ball valve also but they aren't really required. The pushlock fittings aren't cheap and I still need to get quotes for the laser cut alloy block plates so I have no firm pricing as yet, but I need to gauge interest as I don't want to get many more than I need cut.

From my testing this kit makes filling the coolant simple, just top up the radiator, start the car, then fill through the ball valve. One closed it seals the system but allows simple air bleeding as required.

It allows more coolant to circulate through the radiator, keeping temps much more stable. I have done a few track days recently and although the temps rose it was much less than I would usually see, and the stock radiator I am using was coping well. (shame the gearbox didn't stay as cool.) On the dyno the coolant temps were more stable and when pushed it would rise, then drop back to normal straight away making the tuner more confident with multiple high power runs. I feel a larger radiator would still help keep the track temps under more control.

Here are a few instal pics, the hose will require heat shielding from the exhaust as you can see.

post-63525-0-19752600-1349448718_thumb.jpg

post-63525-0-35233700-1349448738_thumb.jpg

post-63525-0-40611300-1349448759_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/410876-m35-coolant-bypass-kit/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

I know you lot don't take me seriously lol.. But this is seriously something a lot of you should be getting on to. Especially after seeing what the little bottle like thing looks like on the head..

I know you lot don't take me seriously lol.. But this is seriously something a lot of you should be getting on to. Especially after seeing what the little bottle like thing looks like on the head..

And you sell it so well.

Why did you have a bottle on your head?

No timeframe as I have no time. lol.

I need to get the plates laser cut, once that is done the rest is fairly straightforward to make. I might do a small run of 10 for now and see how I go. I'm guessing around the $250 mark for the complete kit, hopefully less if I can get some better pricing. Obviously buying in bulk would be smarter too. Anyone got contacts at proflow? :)

No timeframe as I have no time. lol.

Tease! :nyaanyaa:

I need to get the plates laser cut, once that is done the rest is fairly straightforward to make. I might do a small run of 10 for now and see how I go. I'm guessing around the $250 mark for the complete kit, hopefully less if I can get some better pricing. Obviously buying in bulk would be smarter too. Anyone got contacts at proflow? :)

Sounds fine, I'm down for one. Let me know when you've worked out firm pricing etc. Good chance to chuck in the Nismo thermostat at the same time.

The Nismo thermostat is a 5 minute job, this kit will take a few hours Ryan. The injector rail and lower plenum will have to come off. Not a difficult job but time consuming.

I can make one and send it over if you want it soon, I think I have enough parts. Are you able to take some pics and write up an install guide to help out the other guys? I can work you through it on the phone.

Didn't Cam take enough photos for install guide?

The time it takes to complete the job is rewarded, coolant temps are very stable and the fact that you don't have to tip your car upside down to bleed the cooling system makes it worthwhile

I might do a small run of 10 for now and see how I go. I'm guessing around the $250 mark for the complete kit, hopefully less if I can get some better pricing. Obviously buying in bulk would be smarter too. Anyone got contacts at proflow? :)

Check out http://www.anfittingsdirect.com/index.php. I had a quick look & couldn't see weld on fittings, but maybe there is a way around by being creative? Prices look good compared to other suppliers & a decent order (for 10 people) should only add $5 for each person.

N/A if they don't have the bits you need, but possible source for other projects perhaps.

They only seem to sell teflon hose connections Leon, I have this hose but it is more expensive and also not very flexible. It also has a lower recommended heat rating. I think the rubber hose with pushlock fittings is a better way to go.

They only seem to sell teflon hose connections Leon, I have this hose but it is more expensive and also not very flexible. It also has a lower recommended heat rating. I think the rubber hose with pushlock fittings is a better way to go.

I agree, rubber hose is better for this situation. Sorry, I didn't look very hard at what they sold.

Edited by Commsman

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...