Jump to content
SAU Community

Recommended Posts

In the mean time I have been busy starting to do the suspension mods needed for the track. More on the way but here is a start.

Pulled out the entire HICAS system and replaced the power steering pump and reservoir with one from a R33 GTR. Also managed to pull out the all the air con, for more weight saving and then installed;

Hicas Lock Bar

KKR-HicasCancellorKit-Type2.gif

Subframe Aluminium Lock Bushes

SM005.jpg

Cusco Castor Rods

cusco.jpg

Solid Steering Rack Spacer

202501_2011122119.jpg

New front brakes are on, CSC 4-piston calipers with 343x32mm 2 piece rotors

20121117_123607.jpg

Behind the new wheels which are Enkei NT03 18x10+18 all around

20121117_123627.jpg

Cusco front Castor rods and swaybar done

20121117_123533.jpg

Cusco rear swaybar in and HICAS lock bar installed

20121117_123516.jpg

and UAS pivoting front camber arms are good to go

20121117_123546.jpg

Edited by SimonR32

Makes me want a 32 GTR even more now.

Nice buy. Needs P1s, or I refuse to believe this is your car.

Well I do need a set of 17" wheels with good brake clearance for the track haha

Apparently I'm banned from getting another set though, looking at a set of RPF1 17x9.5 +18 for now... Just need to check clearance first

Edited by SimonR32

Good stuff ... love the detail on getting it to turn corners and stop!!

You've done this before??

It's my 4th R32 so I guess I've done it all before :)

Went from

R32 Gts-t RB20

R32 GTR RB26

R32 Gts-t RB25

to this R32 GTR

Hence the final build... Damn things send me broke :whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...