Jump to content
SAU Community

Recommended Posts

So looking at putting coolant my skyline because it getting hot when using only water (coolant leaked then I replaced it with water, hence the heating issue, as there was no issues before when I was running coolant).

Can someone recommend a coolant they have used or a coolant you would advise NOT to use. I have heard organic coolant is good, you basically buy a small bottle then add it to the water in your radiator, anyone used this? I believe it's similar but a bit different to antifreeze/antiboil. Any ideas suggestion advice etc is appreciated, cheers!

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/
Share on other sites

I use Genuine Subaru (Castrol) Anti-Freeze/Boil coolant. Only cause I get them free ;)

I wouldn't use cheap $5 coolant from Supercheap. From my general knowledge, if you use a coolant that isn't antiboil rated, what happens if it boils? it creates pressure and could crack your rad. I could be wrong, but just my opinion. Just use a decent Castrol Anti Freeze/Boil coolant and you'll be fine.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6626548
Share on other sites

Thanks everyone. I've noticed it's been "using" water (I fill up the water then after a while of driving I notice the temp goes up and check the radiator and it's quite low, it's happened twice now, first time I thought I didn't fill it up enough and there was air bubbles). I can't see any leeks anywhere even when it's hot. At first I thought because it was only water not coolant it was evaporating once hot (maybe out of the radiator cap as it was hissing when the car gets hot) but that's not even possible is it? Any ideas on what it could be?

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6626625
Share on other sites

Thanks everyone. I've noticed it's been "using" water (I fill up the water then after a while of driving I notice the temp goes up and check the radiator and it's quite low, it's happened twice now, first time I thought I didn't fill it up enough and there was air bubbles). I can't see any leeks anywhere even when it's hot. At first I thought because it was only water not coolant it was evaporating once hot (maybe out of the radiator cap as it was hissing when the car gets hot) but that's not even possible is it? Any ideas on what it could be?

I've also been told not to use water since it can create rust or algae (in the reservoir) in extreme circumstances, UNLESS it's distilled water. But then again, just don't use it. We have coolant for a reason.

Did you do a proper bleed? If not there may be air bubbles sitting at the high points of the motor. if you drain the coolant completely, it would take about 7.5 Liters (well for my RB25DE Neo in R34 does anyway) to fill it up. If you did a proper bleed then your radiator most likely has hairline cracks in it and only leaks when your driving at 60KM + when coolant is heated up, creates pressure and forces the hairline crack open and seeps out. Doesn't do it when its idle or off since its cooler then and less pressure.

It happened to me before and I changed the rad, no problems anymore

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6626759
Share on other sites

Nissan long life coolant can't go wrong

^^ this ! nissan LLC is in concentrated form when you buy it from nissan, when you add the recommended amount of distilled water to it it works out to be good value too

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627269
Share on other sites

Awesome I'm gonna try the bleeding the water/coolant too, didn't know there was the bleed valve near the plenum lol, I'm also gonna run the heater. Maybe a dumb question but does autobarn or supercheap sell nissan LLC? Or am I gonna have to go to nissan?

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627272
Share on other sites

My stock HCR32 was filled with water when I got it, don't know how long it was in there, but it didn't have any effect on engine temperature, has never been over 85 C and that's while monitoring through consult whist going for a thrash. Have since drained and replaced with the Nissan coolant and temps are the same.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627298
Share on other sites

My stock HCR32 was filled with water when I got it, don't know how long it was in there, but it didn't have any effect on engine temperature, has never been over 85 C and that's while monitoring through consult whist going for a thrash. Have since drained and replaced with the Nissan coolant and temps are the same.

Plenty of people run pure water with no issues.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627519
Share on other sites

im surprised people run just water and havent had too many problems.

Water boils, then evaporates, thats one of the reasons of coolant its anti-freeze and anti-boil

Doesnt freeze over at cool temps and Doesnt boil like a kettle at hot temps

For a few bucks, it gives you peace of mind.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627913
Share on other sites

I was always told. Most 'coolants' are actually an anti freeze(ethylene glycol) and lower the boiling temperature of water. In warmer climates you can get away with just running distilled water and a corrosion inhibitor

I have been doing this for years with no issues, its only like $6 for the inhibitor too! Apparently ethylene glycol can catch fire if you have a high content mix and it sprays over a hot exhaust manifold or similar..

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6627980
Share on other sites

im surprised people run just water and havent had too many problems.

Water boils, then evaporates, thats one of the reasons of coolant its anti-freeze and anti-boil

Doesnt freeze over at cool temps and Doesnt boil like a kettle at hot temps

For a few bucks, it gives you peace of mind.

You water temp. would only sit around the 80 degree area anyway. Even if the water temp. reaches 100 degrees the pressure in the cooling system raises the boiling point.

This is why it's important to replace old radiator caps that don't hold the right pressure anymore.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6628115
Share on other sites

^^^i would be suprised if this was the case for long. . .even distilled water will cause corrosion/ironise on an iron block RB

Do a bit if searching on the forum, it's been talked about plenty if times.

And as for temp issues, no there is no temp issues running just water. As said by someone else, the increased pressure in the system raises the boiling point. Generally cars run about 1 bar of pressue in the system, meaning the boiling point if water is over 120 degrees.

. The majority of coolants are only corrosion inhibitiors, and sometimes anti-freeze. You can still boil the coolant at about 100 degrees if you have a faulty cap.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6628661
Share on other sites

Do a bit if searching on the forum, it's been talked about plenty if times.

And as for temp issues, no there is no temp issues running just water. As said by someone else, the increased pressure in the system raises the boiling point. Generally cars run about 1 bar of pressue in the system, meaning the boiling point if water is over 120 degrees.

. The majority of coolants are only corrosion inhibitiors, and sometimes anti-freeze. You can still boil the coolant at about 100 degrees if you have a faulty cap.

No doubt it has been "talked about" i tried running (only)distilled water in my rb and a week later it started to go brown, no doubt corrosion between the iron block and the water hence why corrosion inhibitors are used by the factory, if they could get away without the expense/necessity of using it they would
Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6629188
Share on other sites

I have been doing this for years with no issues, its only like $6 for the inhibitor too! Apparently ethylene glycol can catch fire if you have a high content mix and it sprays over a hot exhaust manifold or similar..

Its smokey and the distinctive smell of burning coolant goes everywhere, but thats about it.

Link to comment
https://www.sau.com.au/forums/topic/413769-which-coolant/#findComment-6629222
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • oh they were with that motor, you need to remove the engine to change the spark plugs (don't have to, but it does make it easier)
    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
×
×
  • Create New...