Jump to content
SAU Community

Recommended Posts

i have a r33 gts, and recently put a m spots bodykit on her, but now it is way to low and scraps on everything, and was just after some ways i could raise the height, i was told coilovers but idk much about them and if they would raise it, cheers

Link to comment
https://www.sau.com.au/forums/topic/414721-r33-suspension/
Share on other sites

Those heights are just above the minimum legal height. Means that your car is lowered between 1 and 2 inches. You could try to source some new springs (say King's Springs) in standard ride height, or maybe in low (rather than super low) for a lot less $$ than a set of coilovers. Or you could get some BC BRs for ~$1200.

Link to comment
https://www.sau.com.au/forums/topic/414721-r33-suspension/#findComment-6651866
Share on other sites

  • 2 weeks later...

Stock body ftw. Unfortunately this is a losing situation, if you raise your car it will look ridiculous if you keep it how it is you will slowly destroy it. Unless you drive like its a low car even though its not low, it can be done just take the right angles nice and easy when faceing driveways, speed bump etc

Link to comment
https://www.sau.com.au/forums/topic/414721-r33-suspension/#findComment-6674358
Share on other sites

That's the problem with M sports kits. To pull that look off you do need some major low. I was going to buy one but honestly the height issue is why I didn't.

But in saying that I think you'll find that you'll struggle with most aftermarket kits with a lowered car. I had a GTR bar on and that ripped off due to a low ride height, currently I have a 400R and on my coils highest setting it still scrapes.

Link to comment
https://www.sau.com.au/forums/topic/414721-r33-suspension/#findComment-6676088
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...