Jump to content
SAU Community

Recommended Posts

Sounds pretty close to mine (470kw, 20psi)...much the same spec but it is running E85 where as I'm only using 98.

Think I could maybe manage 500kw on E85, but after that I'm sure I would be seriously over speeding the 8374.

Lol i like the -9's on my old mans car but the 8374 is a good 600rpm more responsive from my experience :)

I have full boost before 3800 very happy with them won't change unless I want more power but 350kw is fine for me

I have full boost before 3800 very happy with them won't change unless I want more power but 350kw is fine for me

What if you could have full boost at 3300rpm and make another 120kw on top of that? :)

Edited by Sub Boy32

What if you could have full boost at 3300rpm and make another 120kw on top of that? :)

Then I have other issues with longevity of parts as I track the shit out of my car, hence why I'm not fussed to go over 400kw

What can you do to that setup to optimise it?

The stock manifolds are fine, we both use them, I believe it ran pods as it was a 32. The exhaust wasn't small. It's pretty much a no expense spared car.

It was simply take the -5's off and put the EFR on. Belts it every way possible. Low end grunt, too end power, comes on earlier and back on sooner between gears.

If you could do a back to back between twin EFR's and the single to see the difference, I think that would be interesting but comparing it to what realistically is dinosaur twins (-9's,-5's,2530's,RS's, the trust things) the EFR would belt the shit out of them. This car that I went in yesterday was cracking gates at 4200 on a nugget 2.6 in second gear. -9's wouldn't do that yet the 8374 would supply Atleast another 100 kw of grunt. Between gear, forget it. It was like the gates shut at all. As soon as the clutch was let back out, it was making a anti social noise again.

Hey don't call the 26 a nugget!

Then I have other issues with longevity of parts as I track the shit out of my car, hence why I'm not fussed to go over 400kw

Fair enough, I only take the car out to the track about three times a year and lunched the front diff one of the last times it went out......have since now put a Quaife ATB in it and have been out to the track with no problems other than my shit driving! Haha

.....I haven't run it on anything but 98, so the 470kw is on 98 :)

Thats great, 470kw on 98, easily over 500kw on E85 I would imagine :/

I am hoping for something similar, fully spooled around 3500rpm and 400awkw ish and I will be a happy camper :)

Edited by Nismo 3.2ish
  • Like 1
  • 2 weeks later...

Update:

Engine is ready

Some pics

Nitto I beam rods and custom pistons with a higher pin to improve rod to stroke ratio

post-47556-0-55413800-1423310207_thumb.jpg

post-47556-0-86388900-1423310273_thumb.jpg

Also some new tein shockies, off to race pace for revalvimg, thanks to Aaron for import monster for sourcing

post-47556-0-48533700-1423310367_thumb.jpg

Just a matter of putting the engine in and fixing small bits and peices Pete

The pistons cost me a bloody fortune as they are a custom one off.

I was supposed to go to Perth next week for work but that trips been cancelled, might have it running by the end of the month :D

all good, just get your finger out, if I cannot drive mine, I can at least get some enjoyment out of seeing yours finished and that big stupid grin on your mush :)

So you had the pistons made special for your car, what is the difference, the pin placement ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...