Jump to content
SAU Community

Recommended Posts

to get the r31 started, i took the battery out of my s14. without thinking, i just connected up the leads.

thus putting them on the wrong way. switched them around, all good. the car started.

however, non of the electrical features now work. lights, interior stuff, dash. ect.

i have already checked the in cabin fuses but they are fine.

i know very little about r31s, i can't seem to fine any other fuse boxes.

what do you guys think i broke?

Link to comment
https://www.sau.com.au/forums/topic/416178-battery-on-the-wrong-way/
Share on other sites

to get the r31 started, i took the battery out of my s14. without thinking, i just connected up the leads.

thus putting them on the wrong way. switched them around, all good. the car started.

however, non of the electrical features now work. lights, interior stuff, dash. ect.

i have already checked the in cabin fuses but they are fine.

i know very little about r31s, i can't seem to fine any other fuse boxes.

what do you guys think i broke?

Oh no

Mate you could have killed off half the car !!

the car is neg ground not positive so anything with a relay or fuse , fuse link or diode ( alternator) could be smoked

your going to have to go thru one thing at a time and check the lights too

Your damn lucky if the ecu doesn't have a fried trace or two it would be a miracle of Christmas

Best of luck

I remember when i was about 12 my dad thought he would play mechanic and put a new battery in his old el wagon, nek minnit put it on the wrong way and fried the ecu, 700 dollars later mother wasn't impressed :P

A 12 year old should never take the opportunity (behind Dad's back - but still within earshot), to ask Mum if he can go over to his mate's place when there are chores to be done; that Dad told him to do.

Dads can only 'single-task'!!! :mad:

R31's have a fusible link and relay box behind the RH headlight. You may have fried a fusible link, maybe. But i doubt it.

The other fuse box is inside, RH side of the steering column. This is more than just a fuse box though. This is called the HEC or Hybrid Electronic Control unit. Its also considered to be the SMJ or Super Multiple Junction. Only R31's had them and they are not the most awesome of things. But they dont usually fail either.

This unit has a few purposes; its a place for all the fuses and power relays (can't see the relays without removing the unit), it is the major intersection for everything electrical in the car, and it also houses the electronic control module that controls; dash lights, tail lights, wiper control, interior light, trip computer etc. I dare say you have fried this unit.

If you've still got brake lights and head lights but not much else then its a good indication that its cooked.

You can replace just the electronic module or the entire HEC. Should only take half an hour to replace the entire HEC. Grab one from pick a part.

R31's have a fusible link and relay box behind the RH headlight. You may have fried a fusible link, maybe. But i doubt it.

The other fuse box is inside, RH side of the steering column. This is more than just a fuse box though. This is called the HEC or Hybrid Electronic Control unit. Its also considered to be the SMJ or Super Multiple Junction. Only R31's had them and they are not the most awesome of things. But they dont usually fail either.

This unit has a few purposes; its a place for all the fuses and power relays (can't see the relays without removing the unit), it is the major intersection for everything electrical in the car, and it also houses the electronic control module that controls; dash lights, tail lights, wiper control, interior light, trip computer etc. I dare say you have fried this unit.

If you've still got brake lights and head lights but not much else then its a good indication that its cooked.

You can replace just the electronic module or the entire HEC. Should only take half an hour to replace the entire HEC. Grab one from pick a part.

ill check it out however, nothing works including brake/head lights.

Lights should still work if they are direct fed from a battery source. They are not polarity dependant. So if there not working they must be fed from a Control Module that could be fried.

You might have to get a multi meter out and start checking where the 12v goes into and where there should be an output.

You might need a wiring diagram.

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...