Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Here's Angry35 I detailed this week as an urgent job before a Formal.

Crap pictures as they were taken with my phone. When It arrived it had some clear sap, what looked to be black paint specs, and some silver overspray on it and it lacked depth of shine.

null_zps0afafc68.jpg

null_zps5b598223.jpg

null_zps0ffaafa8.jpg

null_zps6b4bf5db.jpg

null_zpsf37dca9c.jpg

null_zpsd81e7880.jpgnull_zps2fc48bc6.jpg

null_zpsfdeac459.jpg

null_zpsf5b6ae94.jpg

And a few pics from the owner today

null_zpsa3c7f45a.jpg

null_zpse088e4d6.jpg

I've done this car before, and its going up for sale so the owner asked me for a quick pre-sale cleanup. Didn't go nuts with this car removing swirls and scratches, just wanted to make it look decent for the sale. Plus its a not a proper paid job :P

Don't have any before pics but it was in pretty good shape, well looked after and garaged with some usual dirt and grime and lack of wax etc

The outside was washed with Bowden's Body Gel, clayed with Meguair's clay and Megiuar's Last Touch as clay lube. The roof and bootlid had a quick polish with Meguiar's Ultimate Compound to remove some deep-ish scratches, light oxidation and water marks... poor colour match on the rear door/quarter evident in the first pic too :rolleyes:

IMG_20131207_152607.jpg

Engine bay was cleaned with Bowden's Agent Orange and plastics dressed with 303 Aerospace... Wheels were cleaned with Bowden's Wheely Clean and some random brushes, then sealed with Chemical Guys Wheel Guard. Tyres were cleaned with Agent Orange and dressed with Meguiar's Endurance Gel. Wheel arches were also dressed with Bowden's Tyre Shine

IMG_20131207_161825.jpg

Interior got a good vacuum, cleaned with Autoglym Interior cleaner, plastics dressed with 303 Aerospace, leather wheel and gearknob cleaned and treated with Lexol products and glass done with Meguiar's Glass Cleaner.

IMG_20131207_161836.jpg

Door, bonnet and boot jambs done with Last Touch (awesome all-round quick detailer and cheap in bulk)...

IMG_20131207_161855.jpg

And finally, the outside got a layer of Meguiar's Step 2 Deep Chrystal Polish for a bit more gloss and swirl filling, then a coat of Collinite 476s for protection. Outside plastic trims, wiper arms and door frames all got a layer of 303 Aerospace as well

IMG_20131207_162555.jpg

Edited by junkie
  • Like 1
  • 4 weeks later...

Man you guys are good at detailing, I could not be bothered and I don't have a clue haha, my mate just had his supra done by this bloke. http://www.detailparadise.com.au/showthread.php?10605-Moonstone-Silver-Toyota-Supra-Correction-Cquartz-Finest

My r32 was booked in for this week but I had to cancel to next week, can't wait till it's done. I will post up some pics

All your cars and work look great.

  • 2 weeks later...

cheers guys...Scott i thought you would of seen it on FB mate..

Paint was Debeer base and Body Shop generic acrylic clear...rubbed it with 1200 then some finer sanding pads (2-2500 maybe) and buffed with fg500..pretty simple really..though time consuming...clear could do with some more finishing work but there is only so much effort I am willing to put into a toyota Echo :P

i was amazed how well the colours blended together actually..I cant even really see the blend lines now

DSCN0765_zpsfabdd8e1.jpg

Been a while so I might throw up a few of a S5 I did recently.

I Foamed the car down with AMMO Foam.

Clayed

2 Stage Paint Correction with Menzerrna 2000 & 4000

Applied Ammo Skin and Ammo Creme

post-11799-0-94448600-1390256274_thumb.jpg

post-11799-0-77146400-1390256205_thumb.jpg

post-11799-0-63480700-1390256210_thumb.jpg

post-11799-0-67501100-1390256215_thumb.jpg

post-11799-0-37749600-1390256219_thumb.jpg

post-11799-0-12125900-1390256239_thumb.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...