Jump to content
SAU Community

Recommended Posts

Is the last photo supposed to be up there?

looks as though the rear seal in the gearbox is leaking slightly, hard to say for sure from the pictures but looks like it has a slow leak and as you drive along it pushes all the oil back into the exhaust

It had a heavy duty clutch put in just before I bought it so guessing the mechanic did a shit job?

The fluid on the exhaust is dripping down from above.

Theist pic I thought I'd pic there just in case and if I don't get an answer for it I'll post it in a thread on the suspension section.

What do I do about the leak? Take if back to the mechanic and get him to do if properly this time?

Thats a leak?

I can't see where it's actually dripping.

Even if it is leaking, it's an advanced anti rust feature that slowly administers an advanced lubricant to the under carriage. Ingenious design!

R33 GTS-T

With regards to the last picture what I experience sometimes is a similar sensation to driving over one of those street lines that has all the bumps and kind of hums. So I figured the tyres were rubbing on something. And if you look in the pic on the bit of metal above the wheel you see it has been rubbing on that but I can't find a particular circumstance when it occurs. Probably happens most when going downhill.

Yeah I wouldnt stress about that, I have about the same gap on my UCA and dont have any issues. Is the rubbing in a straight line or when turning, I think from your description it is just straight driving. Its not the tyre rubbing on the inner guards or anything like that? mine does that sometimes.

O.K so where it is rubbing should move with the wheel as it is attatched to the hub. Should be able to see what I'm talking about from these screenshots:

This is the front hub:

fronthub_zps7ab27689.jpg

I've circled the bit in red to match it up to the front suspension:

FrontSuspension_zps48bb9f16.jpg

So the red bit is what joins the hub to the arm that you can see rubbing on. So the only way I can see the tyre rubbing here is if you have to much wear in the 'king pin' or somewhere there. It shouldnt be able to rub there as it should move with the tyre/suspension so I would check around there to make sure there arent any problems

Perhaps take it somewhere for a suspension check. Like pedders etc and tell them what its doing

Edited by 89CAL

Not in the engine bay, that's for sure. You know where the gearbox is? The fill hole is on the side of it. Check level there. Car on hoist stuff.

Yeah I thought it probably was, was hoping for an easy check I guess. Need a hoist? Can't get under there with a trolley jack and stands?

O.K so where it is rubbing should move with the wheel as it is attatched to the hub. Should be able to see what I'm talking about from these screenshots:

This is the front hub:

fronthub_zps7ab27689.jpg

I've circled the bit in red to match it up to the front suspension:

FrontSuspension_zps48bb9f16.jpg

So the red bit is what joins the hub to the arm that you can see rubbing on. So the only way I can see the tyre rubbing here is if you have to much wear in the 'king pin' or somewhere there. It shouldnt be able to rub there as it should move with the tyre/suspension so I would check around there to make sure there arent any problems

Perhaps take it somewhere for a suspension check. Like pedders etc and tell them what its doing

Yeah can't even understand how it's possible...

just undo the bung on the side of the gearbox (with the car level of course). stick your finger in the hole, there should be oil right up to the hole, but no more. if you have to shove your whole finger in there and reach down to find it, then it needs a top up. i had the same issue recently. the seal itself is cheap and easy to replace, but the exhaust and drive shaft need to come out to do it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...