Jump to content
SAU Community

Recommended Posts

are the grill mounts detachable for the n1 headlamps? or are they moulded to the housing? iv seen some n1 types that have the mounts and some doesnt have it..attachicon.gifimages.jpgattachicon.gifpicture008g.jpg

With mounts = R32 GTR N1 headlights, to secure front grill.

Without mounts = R32 GTS-T headlights.

With mounts = R32 GTR N1 headlights, to secure front grill.

Without mounts = R32 GTS-T headlights.

This is not entirely correct.

No the standard GTS-t's did not have the clips for the grill, although they did have screw holes for an option to fit the brackets (which were metal) for a GTR style grill. You can get these through NISSAN. So any reflector style (N1 style) headlights that have the brackets which are held on by screws and are removable, are NOT genuine N1s.

The genuine N1s have the brackets which are plastic and are molded into the body of the headlight itself. These are NOT removable.

This is not entirely correct.

No the standard GTS-t's did not have the clips for the grill, although they did have screw holes for an option to fit the brackets (which were metal) for a GTR style grill. You can get these through NISSAN. So any reflector style (N1 style) headlights that have the brackets which are held on by screws and are removable, are NOT genuine N1s.

The genuine N1s have the brackets which are plastic and are molded into the body of the headlight itself. These are NOT removable.

Sorry Damien but that is not accurate.

(OO)SKYLINE(OO) is right.

Genuine N1's do not come with plastic brackets molded into the headlight. Standard R32 projector type headlights do.

If you were to source N1 (Zenki) Headlights from Nissan they come with metal brackets that are bolted each N1 headlight.

GTS'ts have N1 type headlights without brackets and can sometimes fool people that they are genuine N1 headlights.

I have both sets (with N1 recently purchased) be more than happy to post up pics for comparison.

Edited by Ants

Hey Ant,

I spoke to Kudos (SAU trader) about 6 months ago about this same thing as i was after genuine Zenki N1s, and he supplies them direct from NISSAN Japan, and he assured me the brackets were molded plastic (like the GTR projectors) and are part of the body and not removable. This is what distinguishes the difference between the N1 and the GTS items.

I did a fair bit of research into this as i was searching for a set myself, and i found a lot of conflicting information and could not get a straight answer, so i spoke to a specialist who deals in new original Nissan parts.

Ill ask someone on here who i know purchased a set through them so i can get a straight answer and ill let you guys know.

i prefer my projectors ;)

i wonder why they never moulded the braket on?

Well I have both. So change it when I want :yes:

No idea why N1's were not molded on - maybe it was in case they got damaged in racing it was easier to fix up :closedeyes:

Well I have both. So change it when I want :yes:

No idea why N1's were not molded on - maybe it was in case they got damaged in racing it was easier to fix up :closedeyes:

hmmmm, bolts=metal, they should be moulded for light weight :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...