Jump to content
SAU Community

Recommended Posts

when i purchased my gtr, the owners brother(owner wasnt there, everything was legit, so all good), handed my os giken twin plate(needed rebuild).

looked underneth, had tien coilovers.

trust 4inch cooler.

tuned y pipe, 3inch cat and cat back.

those were the parts i didnt know of.

did you check and see how good the ah 'mines ecu' under the back seat was, or did you just throw it out?

Tossed it ,it was not in very good condition,i think it had been there a while.

Edited by I gotta R34gtr v-spec

I bought my 34 a long time ago.. About 2 years after i bought it i went to install red bulbs behind my dash. I took the dash apart then went reaching in behind there and found some wires that seemed a bit "out of place".. So i looked up under there and followed the wires back and found a Greddy full auto turbo timer sitting in there!? hidden amongst all the other wires. All i had to do was turn it back on and mount it and boom. Free turbo timer. :D Also found a Japanese jdm game token coin like thing under my seat..

Found a 1979 20cent piece behind the roof vinyl interior of my 1981 Stanza. So I can only assume the coin was lost there while the car was on the assembly line. Still have the coin somewhere....

Jeff

  • 2 months later...

Found yellow jackets tucked down the left side of my r32's boot still in there packets! (Hopefully will fit my rb20) :)

Was looking at buying rear hicas lock bar.. Had a look underneath and already had one :)

Nismo front strut bar with Nismo stamped into it (hopefully genuine.. Not sure if those are even rare..

And last but not least about $18 worth of shrappaz!

In my 33 i Found split fires, dodgy wiring in the tail lights, really old jdm gaff tape in the doors, wierd wires all through the car, a USB with the guys birth certificate license and all his tickets, jdm coins, aus coins $14 worth, Japanese rego sticker

And the classic dried up maccas chip

4 children's nursery rhyme CDs behind the dash, played that shit all day!

Shell battery from Japan? You can't buy them here.

Shell service stickers all over and in the car from Japan.

On my gf car I found a threaded head with the spark plug sitting on top and some more threaded bolts on the thermostat housing. It was a fluke it even ran.

found tanabe GF210 on my stock springs heh i knew them orange springs were weird! also found the lock nut key from previous owner's set of nuts, which he had the tyre guys smash off, thus running only 4 nuts (until i bought a new set of nuts). what a nub. it was in the compartment which had the spare tyre jack in it, i noticed something rolling around inside.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...