Jump to content
SAU Community

Recommended Posts

yes i am running the ID1000s with the resistor pack removed, 1000cc is enough for me with -9's.

you dont have to run ID1000s you just need to remove your current setup and test it with a stock setup to see if this is the issue or not.

what turbo are you using to need more then 1000cc ???? even with e85 that is quite a bit of power.

He is running Bosch ev14's 2000cc (xspurt) injectors, brand new. I doubt there is an issue with them, and I though Jez already tried another set of injectors? While I agree the 2000's are not as reliable as the 1000's due to being natural gas injectors there are plenty of people using them without issue, and Portaz is still running 98 so e85 can't be blamed...

Out of interest, which version firmware were you running in the select ECU with the misfire problem? With the Nissan trigger there was a problem above ~6000rpm between versions 10.105 and 10.126 which has been remedied in 10.0127. If your version was outside of that range then it must have been something else.

its not because its wasted spark. even the plug in vipec / link is using wasted spark and people are running massive power on those, ive seen waste spark pushing over 1500hp with no issues on really dirty engines

+1 agree it's not because you were running wasted spark, especially on Nissan coils which only need 1.8ms of dwell time. If you do that maths at 1.8ms dwell a wasted spark setup could support up to around 12,000rpm. Interested to hear if it was a FW issue, The e1280s will give you full sequential fuel delivery, end of injection timing and whatever fuel/ign calcs your tuner might want to dream up if he's competent with the advanced view interface though.

I should clarify , same tuner same dyno different style of ecu, I must say I thought jez may give up as he flys out on hols soon but he is about as stubborn as me and it seems Andy is too really thanks guys even though we havnt completed e 85 tune I'm really stocked and adjusting dwell made no difference, well what ever it is that's the cause the nistune didn't suffer same issue not sure on firmware though I'm sure the boys looked at it

I did suggest injector timing as in 360 or 720 (not sure exactly ) but on select its not adjustable in the 1280 it is but what's strange is there was 2 cars there running same ecu injector setup with no issues so its a but of a mystery till Wednesday , I've researched that when the Japanese change engines in r 32 they always put a new engine loom in if that's true maybe there's a reason for it I guess

Either way it sounds like you're on top of it, from an engineering perspective it would have been nice to identify the issue before blanket fixing it with another ECU. Injection timing adjustment is available on v10.127 now by the way but it's only injector phasing (so the adjustment is in 120 degree steps on a 6 cyl), not injection end angle adjustment as is the case the with the 1280.

so he has other cars there with the same ecu and same injectors but there are no issues ???

ooooo i love head f**ks like this. wish it was me. i would not be changing the ecu i would be trying to find whats causing the problem.

never give up

I'll be buying it in the next week. Been talking to Andy aswell just trying to get my head around the VE tuning and all that.

I've had a play with WARI and am much happier with in in regards to usability over haltech and vipec software.

Because of my limited mods it seems i can use the base ignition and fuel maps. Once i get it i plan to make some changes to the base fuel map using my wideband and the fast tuner.

well the software is very different from all other platforms that i have seen. once you know where everything is its pretty good.

i never use the fast tuner... let us know how you go with it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...