Jump to content
SAU Community

Recommended Posts

Stagea Humans,

Just wondering if anyone is running 20s on their M35 and what specs they are? Looking at some 20x10s in a +38 which should theoretically fit, but would like to know what others have. Pretty handy with the old guard roller after all these years so a little bit of massaging is no issue.

Many Thanks im Advance,

Jeff

Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/
Share on other sites

Yes I agree with Alex I think you will have issues on the inside not the outside, I have 19*9.5 +35 and there is very little room to the suspension I have around 3mm to the strut.

Edited by richzx
Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/#findComment-6807188
Share on other sites

I only put them on Thursday and nothing as yet. I think a few others have run the same spec with no issue. When I think about it there must be more room because I tried on and drove with some 19*9.5 +38 as well. I will double check. I also have the Bilstein suspension in mine if it makes a difference?

Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/#findComment-6807270
Share on other sites

Wheels look ok but you need more offset or some spacers!

The killer is the Over Fenders.

The steelwork underneath is the same as the RS/RX, but the guards protrude out another 15 or 20mm, so you can't push the offsets too far unless you start cutting metal or going bananas with guard rolling.

Also, I think they need some more sidewall; the guards just swallow the wheels up with super low profile.

Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/#findComment-6807657
Share on other sites

Question for yah. If I run 19 x 8.5 I'm gay aye? Pity I cannot fit wider because I'd be hardcore like you then! IMO on the m35 if its white its gay!

Pfft. My 18x8 white rims look awesome! Could do with a fraction more sidewall though...

Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/#findComment-6807849
Share on other sites

Anything under 8.5" wide is not even a worthy upgrade IMO.

And if your into handling, make sure your 20's are not Tempe tyres/ taleb tyres / ozzy tyres specials.

Stuff I could cast a better circle in my daughters sand pit!

Better have bucket of lead to balance the suckers to.

Really a well made 19" is the performance limit.

Anything over your adding to much Unsprung weight and tyres will cost you a heap.

Just my 3 cents

Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/#findComment-6807964
Share on other sites

My 2c

First, the one car i have seen with 19x10+ wheels looked horrible. To add, it was also dangerous.

Second, people think buying wide rims and putting Ling Long tyres on them makes them a handling God. I'll take 30mm smaller, quality tyres over china spec any day.

And Christian, maybe you should check out what fits before offering advice. Not many of us are StanceNation orientated.

Link to comment
https://www.sau.com.au/forums/topic/423056-20s-on-m35/#findComment-6807979
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...