Jump to content
SAU Community

Recommended Posts

Hi guys,

Just found out that my bottom end is fine and that the problem piston rattle..

my question to you guys which I cant find a answer for anywhere is how safe is it to drive with piston rattle.

The engine is a fresh rebuild with old pistons and rods but everything else is pretty much new.

its very faint sound to the car warms up then you can kind of hear it .

oh and its in a R32 GTR with a RB26DETT

Thanks all and if u have any questions ask me

Edited by mick1223
Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/
Share on other sites

Well i would be getting out sorted asap. Goes to show you can't cheap out on a rebuild, ends up choosing mire doing it twice. What about the other parts you claim are pretty much new? Maybe revisit those when its apart the second time.

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6817712
Share on other sites

Well I would consider piston slap bottom end, seriously consider a different builder it amazes me he would put old pistons and oil pump in an rb26 I'm my opinion it should have stayed in pieces waiting for new parts due to the labour involved in pulling one out and stripping it down, anyway if it were mine I wouldn't drive it.

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6817805
Share on other sites

Why does everyone say bottom end. I just had my bottom end done.

Is it really that unlikely to be piston slap

the pistons ARE part of your bottom end anyway!

wether it be pistons or bearings that motor is waiting to fail

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6818397
Share on other sites

Why does everyone say bottom end. I just had my bottom end done.

Is it really that unlikely to be piston slap

Simple answer, because pistons ARE part of the bottom end, something you need to understand unless you want this workshop to continue feeding you horseshit.

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6818426
Share on other sites

The engine is a fresh rebuild with old pistons and rods but everything else is pretty much new.

When an engine is built, critical tolerances are measured, including bore to piston clearance.

If your engine was assembled with that out of spec, I would run as fast as possible from that guy!

+1

Hence why it should be built with new Pistons and Rods.

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6818595
Share on other sites

Yep +1 to Steve/Nick

Piston slap just means it was a shit build to start off with. In this day and age there shouldn't be any at all if the motor is built to correct tolerance.

Agree.

I paid a good machinist to do my bores for this exact reason. Am using CP's in an SR and they are dead freaking silent.. They measured the pistons themselves and determined the bore size from there.

I've heard enough SR CP slap stories to last me a life time. Cheap shit builds.

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6818628
Share on other sites

^^ at least with new pistons there would be a valid warranty claim- using secondhand pistons the original engine builder could tell you to get stuffed, im all for using secondhand parts but im aware that im taking a chance

Link to comment
https://www.sau.com.au/forums/topic/423641-piston-rattle/#findComment-6818836
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...