Jump to content
SAU Community

Recommended Posts

It will be my very first race. Excitafraid is the term we have created for how I'm feeling about it :)

We have another new addition to go into the car - the new Motec CDL3 track kit with the upgraded SLM.

Basically these can be configured to go into any car (no Motec ECU required) but are really easy for cars with an OBD port / CANBUS system. GPS based lap timing with automatic track recognition so no more putting becons out or programming the unit for each track you go to. The SLM can be programmed to give warnings for any settings read through the canbus or any other interface you use. So you can set warnings for engine, transmission, water temps, knock - whatever you like really. And it obviously acts as a shift light as well. Plus the I2 software is as good as it gets for data analysis when looking at lap times and comparing things like braking points at even lines through corners with the GPS tracking.

1045237_10152024040237564_1096824809_n.j

Another thing I've had to get was different sized uprights for the Aeromotions wing. Regs state the max wing height can only be 250mm from the boot lid at the centre point of the car. The old height was about 295mm. With these new smaller ones it now sits at 249mm.

1005898_10152024304027564_488519888_n.jp

Another thing I've had to get was different sized uprights for the Aeromotions wing. Regs state the max wing height can only be 250mm from the boot lid at the centre point of the car. The old height was about 295mm. With these new smaller ones it now sits at 249mm.

1005898_10152024304027564_488519888_n.jp

Hey snowman, not sure if your gonna add a front splitter now or later but curious if running the lower uprights gives you less rear downforce. It may end up balancing the car and loosing that under steer you have.. Not sure but would like to hear your feedback if you try. Cheers

Steve - I want to run a front splitter and I have one ordered from Powerhouse Amuse. Unfortunately it's not due to arrive until August so I won't have it for the first event.

I hope Miles doesn't mind me using his pic but this is the same unit as he runs on his beast. The main benefit with the Amuse unit however is in their under-side design.

530054_409101679145881_1651675475_n.jpg

amuse_frontlip2.jpg

That front splitter will definitely help, it's great that you can buy one already fabricated to fit your vehicle. Since you won't have it on for the first event please give feedback in regards to front grip, not even sure if you will feel any difference but still curious.

Edited by stevena

More work has been done. The event I did earlier in the year at the Australian GP showed a continual rise in engine oil temps over +15min runs to the point where oil temps were getting to worrying levels so a second oil cooler has been installed into the centre of the car similar to the pic below (I don't have pics of my set-up unfortunately but this image was the basis for what we did)

P1080117.JPG?psid=1

The other big issue we have faced with the car to date has been brake temps. To date there are no real brake ducting solutions available for the R35 so the boys at Racepace have come together with the fabrications guy at Kelly Racing to design a custom brake cooling duct. At the same time they are also designing one for Chris' R33 GT-R.

Again I don't have pics of the first step - but that was to come around with some balsa wood and sculpt the basis of the shape for the duct mould.Once they had this they were able to cast the initial duct which was deliberately made oversize in length. The construction is also made with a special high temp resin that is also designed to self extinguish in the event of a brake fire. It's the same stuff they use on the V8 Supercar duct construction.

1045148_10152027539002564_1118941019_n.j

Next step was to check clearances with the wheels at lock.

944485_10152027538907564_1317946432_n.jp


The calliper and rotors were then removed and the duct is trimmed to make a neat fit on the back side.

995693_10152027538817564_1117918211_n.jp

Then the calliper was bolted back on and the front was trimmed to match as well. This intersects right along the edge of the calliper so that there is clearance for the brake lines.

580465_10152027538752564_282639267_n.jpg

Next step is to show how we are collecting the air into the ducts and I will post that up when it is done.

  • Like 1

Dane - The state series are 4 race weekends. Sandown races are 8, 10, 10 and 12 laps and PI are 6, 8, 8 and 10 lap races.

The enduro races (Island Magic and Bathurst) are again 4 race weekends but they consist of 1 x 5 lap for driver, 1 x 5 lap for co-driver and then 2 x 1hr races with 1 pitstop each race for driver changes (no refueling however).

Anyways - I have some more car updates. I have the new doors and side window's back from Raceglass.

Rear 1/4 including the inner mould which the window sits in. Looks stock!

944533_10152041584797564_30258860_n.jpg

One of the front door window's.

1006207_10152041584782564_1160980327_n.j

One of the doors - total weight is 6kgs.

996795_10152041584802564_1162437692_n.jp

Inner side of the mould.

1014397_10152041585007564_532025936_n.jp

And fitted to the car. Color match is amazing so no painting or anything required.

1005169_10152041585027564_2023051288_n.j

  • Like 1

Looking great, even since I had a look a few week ago!

If you're struggling with any of the dash setup let me know. Also I can check your config to ensure you get the best data you can out of the CDL3!

I'll try and make it to the race in a couple of weeks too.

Cheers,

Darren.

Cheers Darren.

What would be SUPER would be if you had the CAN protocols for the gearbox so we could log what that is doing as well. I got most of the engine stuff from Lee but I don't have anything as yet for the gearbox.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...