Jump to content
SAU Community

Recommended Posts

  • 2 months later...

None of those on the recommendation list have been proved or deemed guilty of odo tampering during recent investigations.

I'm not saying that none have done it though.

I bought a car of Nagoya motors on paramatta road my V36 350gt, but the car seems very good and i haven't had any problems with it yet ... touch the fake wood interior :P so id give them the thumbs up.

I bought a car of Nagoya motors on paramatta road my V36 350gt, but the car seems very good and i haven't had any problems with it yet ... touch the fake wood interior :P so id give them the thumbs up.

How long ago and have you checked the k's?

  • 2 weeks later...
  • 1 month later...

I bought my 250GT from Nagoya and very happy with it. I have my doubts about the kays and the honesty of the dealer, but bought the car based on condition not the mileage. No accidents, very straight body, nice paint, super clean inside with very little wear, no dodgy repairs, rust free, etc... came up really well after a full detail too.

Two years and 20,000km later, its been faultless (knock wood) and gets driven 90km each day. Only things I've had to do is replace the crappy soft front rotors and dumped the factory single cd player that had some jap pop cd stuck inside

  • 1 month later...

First time importing I went with Iron Chef and got a Mark X, I am happy with the car but I don't think I will use Iron Chef again, the lack of communcation and some email's not getting replied back, had to chase up the complaince shop to see if the car had arrive and when it will be ready and organise being registered myself. A bit disappointing but other than that I am happy with the car.

Edited by flatlinerz

^that sounds pretty normal to me. Once it's on its way to compliance I dont think the importer should be ringing around checking up on your car. I had the details of the transport company who informed me once it arrived in my city, but from there it got picked up by someone local.

From compliance till registration really isn't importers problem unless something has occurred from either during transport or from the auction house.

Waiting for compliance , getting a certificate and finally registration has nothing to do with the importer either.

  • Like 1

post-135824-14222485750126_thumb.jpg

Iam currently going through iron chef,

They are brining over my MNP II Bnr34 V-spec

I have found them to be good at responding,

Every question I have asked they have given me in depth responses to cover any thing I need/should know .

would recommend them

  • Like 2
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for that mate always a good help
    • It's not really a calibration issue, if the voltage is really at 2V. If the voltage is 2V, then that's what the TPS is putting out, and the Haltech is seeing that and 2V is about 40% open (you know, between 0.45v being closed and something close to 4.5V being fully open). So, that would suggest that the TPS is maladjusted, on crooked, something something something. Or a wire problem.
    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
×
×
  • Create New...