Jump to content
SAU Community

Recommended Posts

motor:

S1 RB25

Z32

bigger inj

power fc

splitfires

ect ect

car runs, idles drives perfect until about 5000rpm in any gear, same spot in the rev range each time it will just start running on one or two less cylinders, clutch in and free rev and it goes away and runs perfect again

the Power FC is brand new, was still doing it with the Nisstune the car came with

the Splitfires and spark plugs are brand new

car was put on the dyno and tuner suspected there was a missing earth somewhere in the loom, but has been checked over and theyre all there so im a bit stumped

any help would be appreciated

one thing I havent tested which i will tnight is if it still does it when cruising and getting the revs up on half throttle for examle

Link to comment
https://www.sau.com.au/forums/topic/428267-s1-rb25-weird-problem/
Share on other sites

new symptoms

was running rough while driving, gave it a free rev and at 5k (wouldnt go past 5k) coughed and spluttered and then shut up, clutched out to start again and wouldnt start, pulled over, turned key and started was spinning but motor not cranking, left for 2mins, started up fine and ran fine again???????????????

Have you got laptop or commander for it?

yup have the hand controller in the glove box

Spark plugs (cracked) caused revving problem and wrong injector seals caused similar symptoms for me. Took ages to diagnose and lots of swearing.

will check plugs, someone also suggested a vac leak, maybe good idea to put smoke machine through it? can rule out vac leak and injector seals at same time

Pressure testing the intake would be a good idea, and check the vac lines to the fuel reg/map sensor if you are running one.

shall try get the smoke machine on it on the weekend and yeh has Turbosmart FPR

Well, in that case, there's a sensor check function on the commander. Just find it and use it.

will do tonight, thanks for that

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...