Jump to content
SAU Community

Who's Running A Wideband And What Are You Using?

SS8_Gohan

By SS8_Gohan,
in Engines & Forced Induction

 Share

Recommended Posts

Hanaldo Grand Master

Hanaldo

Posted
Posted

Well when I first got the AEM, BEFORE I had any suspicions about it's accuracy, my tuner actually commented about how accurate it was. Said it read dead on exactly the same as his. I'm only suspicious now because of how rich it reads, but that could well be my tune.

  • Replies 129
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Hanaldo
Hanaldo

I'm using an AEM UEGO as well. Thing is, I'm not totally confident it is 100% accurate. I have a feeling it might read a bit rich, otherwise my tune is extremely rich. Frequently seeing ~12.5 on cruis

Dose Pipe Sutututu
Dose Pipe Sutututu

if you're using the serial out on the wideband to the adaptronic then don't worry, the ecu will know the sensor is offline.. if you're using 0-5 to out.. and analogue in.. when the wideband fails ecu

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

i'm sold, techedge it is

http://wbo2.com/2j/2j9.htm

So all i need is 2J9 + cables + sensor? (17123)

Yup.

it is a good idea to grab a LX1 display to go with it if you can afford it. that way you can be sure the input settings are correct in the software on your ecu because you can compare it with the external display, also if the car leans out when your into it you can see it on the fly.

Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

I got this depo gauge...seems all right has Bosch sensor..

Started reading lean, turns out my fuel filter needed replacing...replaced fuel filter now wideband reads error...tried to calibrate it but no response.. :unsure:

Pretty sure sensor is still fine , if unit is dead can I just get the techedge so I can link it to my adaptronic?

start again and get a new sensor with the TE. peace of mind is a good thing and they are not very expensive anyway.

I am pretty sure depo is a china brand.

ARTZ Grand Master

ARTZ

Posted
Posted

Not sure, Says Japan on their site, was about the same price as AEM so figured it was an entry level unit...hopefully I can get it up and running again..its a cool little gauge but can't find the instruction booklet to figure out why the error code...

  • 2 weeks later...
Ryno Experienced

Ryno

Posted
Posted (edited)

Good timing for this thread to pop up... I'd just decided to drop some coin on a wide band unit that I'll have wired in permanently, when I noticed this thread.

I had my eye on a Koso unit from the states, but after reading Guilt-Toy's advice I think I'll go for an 2J9 Tech Edge unit with LX1 display.

Edited by Ryno
Missileman Veteran

Missileman

Posted
Posted

Crunch the numbers and find the price difference between the 2J and the 3A models, remember the techedge site doesn't quote gst, the initial pain to your wallet will soon pass and it's much cheaper to buy right the first time.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

just curious on why people prefer the tech edge over all in one units such as AEM UEGO, Innovate MTX-L, LC-1, PLX?

Is it because it uses the BOSCH LSU 4.9 sensor instead of the LSU 4.2 sensor?

Missileman Veteran

Missileman

Posted
Posted (edited)

I bought mine mainly on reputation, a few of the tuners I've spoken to use them, and have told me the people who design and build them know their shit and they are built to a standard not a price. As for the all-in-one gauge and driver, I would have liked a gauge but this was only a secondary consideration, accuracy and quality took priority, after all this is a tuning tool not another dial to rice up my dash. Also the driver will accept uego and multiple bosch sensors.

Mike.

Edited by Missileman
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

^ fair enough, I don't use widebands to rice up my dash either. I've always used all in one units to street tune my car and my friend's cars, one thing I've notice is that there's always a little lag time between the pedal being depressed vs. the readout from the widebands I've used.

Missileman Veteran

Missileman

Posted
Posted (edited)

I posted the nistune graph in your other thread and you saw how little lag there was when I jumped off the throttle at 60, about 1/3 of second lag, and that was at minimal gas flow. I believe the techedge gauges would read at the same speed/lag as nistune.

bosch 4.9 mounted before the cat

Edited by Missileman
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

See how we go :)

I've recently just installed a AEM UEGO gauge on my mate's S15 just right before the cat (japanese downpipe already had a pre welded bung). I'm plugging up his Nistune either this weekend, just waiting to see if his missus will let him out for a day haha

ARTZ Grand Master

ARTZ

Posted
Posted

ok....reasons im getting an error or code "03" (as it appears on my unit)...have tried to recalibrate but pushing its button does nothing....

bosch sensor has barely 3000km on it...originally had this problem with not getting enough power, but I fixed this when I rewired it...unit is getting 12v or thereabout and it was working fine until I changed a fuel filter, I also drained the tank a few times...none of which should have any effect on the wideband I thought...i did have it running too rich for a while, have fixed that... pulled sensor out and looks clean...

Anyone got any ideas here, I'm stumped ?

  • 5 weeks later...
omnigear Proficient

omnigear

Posted
Posted

Have you check if the O2 sensor is heating up?

ok....reasons im getting an error or code "03" (as it appears on my unit)...have tried to recalibrate but pushing its button does nothing....

bosch sensor has barely 3000km on it...originally had this problem with not getting enough power, but I fixed this when I rewired it...unit is getting 12v or thereabout and it was working fine until I changed a fuel filter, I also drained the tank a few times...none of which should have any effect on the wideband I thought...i did have it running too rich for a while, have fixed that... pulled sensor out and looks clean...

Anyone got any ideas here, I'm stumped ?

omnigear Proficient

omnigear

Posted
Posted

this, i have a faulty unit and even though the voltage was being sent to the sensor it would not heat up. you can light a cigarette if it works =p

Take the sensor out of the exhaust and feel it. If it gets hot quickly it is working. Careful you don't burn yourself...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...