Jump to content
SAU Community

Recommended Posts

So i got a new rb20det and its running standard 20det sidemount turbo , i want to put my t3t4 back on but its ennificient on a 20 kicking in around 4000-7000k i heard if manifold is shortened it will kick in quicker and be more effecient , is this true and is it worth it ?

idk i was just told this by a mate and i wasnt really paying to much attention but i would assume turbo manifold , i just want more boost out of it and i already have the turbo so it would be good if i could run that but have it kick in lower revs

yea stock manifold sidemount , thats what i was thinking but he said hes done it before and its a piece of piss so idk haha but it doesnt sound like something you would do i guess i would have to look into it more but i agree hacking into manifold doesnt sound logical haha

you can disconnect the actuator

Yep, easiest and cheapest way to unlock max boost, pull off wastegate line. (seeing as you got fairly confused about the manifold thing, that is a joke)

Tell whatever hybrid turbo you have. Buy a NEO6 turbo, it bolts straight on. Put the RB20 actuator on that and enjoy 10psi. It kicks in around 3,000rpm (probably a bit earlier if you had a full exhaust). Good for some fast driving, better fuel economy while putting around. Win win.

this applies to manifold pipe diameter, bigger pipe = more lag but some top end power, where as smaller pipe is more response but top end power is reduced

so stock manifold is more responsive due to smaller diameter pipe

you might have a boost leak or if not your running a r33 turbo/actuator for that 6psi

sounds like its normal for an ebay t3/t4 turbo (whatever that is who really knows) to spool extremely late on a 20. you cannot shorten the maniifold someones just talking crap to you. better off selling it and putting on an rb25 standard turbo. car will be like new car to drive, will be so much quicker and more enjoyable.

Op6 rear housing is a little big for a 20, considering you can't run a lot of boost through them I wouldn't bother, better of selling one he has and buying a 2530 or similar, at least will have the potential to make decent power and have great spool.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...