Jump to content
SAU Community

Gear Box Suggestion R33 Gtst

sime1
 Share

Recommended Posts

sime1 Collaborator

sime1

Posted
  • Author
Posted

Hey mark I just spoke too uni group the boat got 437kw on 28 psi then the turbo started to produce hot air and also had a few minor petrol leaks which they are fixing then it's going back on the dyno I'll be back in Sydney in one week will msg you when I'm taking it too track

The Bogan Grand Master

The Bogan

Posted
Posted

The stock box will take the power as long as you have some mechanical sympathy.

I got the stock box rebuilt and modified but at the drags with sticky tyres and sticky track it started to chew the case hardening of the gears after about a dozen runs, the oil I used was good quality, and I even swapped out the oil and added some modifiers to try and slow the wear but to no avail.

When you are pushing a heap of torque the stock box might be fine for street duties or the occasional squirt , but when it gets leaned on it is found wanting.

Disclaimer: This is from my experience of 2 gearboxes and talking to people at the drags, most overcame the issue by installing a slush box.

  • 2 weeks later...
sime1 Collaborator

sime1

Posted
  • Author
Posted

Hey mark I got the car back from uni group I took it to the runs but was only allowed to drive it on low boost cause the ethanol was not above 60 so there for didn't call u out I take the car back there on Friday for another dyno session car made 437 kW then turbo max out I got an 11.8 on low boost 21psi after they dyno it on fri then she will be ready for hi boost 28psi I need new mickeys for rear I could not get traction what's so ever I should be going next week if not def following week will let you know when she ready 4 hi boost and come down... Quick question I noticed under hi torque and lots off pressure the engine light flashes on sought of off through the gears only under high revs take off and stuff did you ever notice engine light come on and off at all when u owned....

GTSBoy Grand Master

GTSBoy

Posted
Posted (edited)

PowerFC? Engine light flashing is knock indication isn't it? In that case, happening at high load makes sense.

Also, try distributing the full stops in your above post around the post a bit more evenly. Leaving them clumped up together doesn't work. I have a headache after reading it!!

Edited by GTSBoy
chez00 Contributor

chez00

Posted
Posted
I got the stock box rebuilt and modified but at the drags with sticky tyres and sticky track it started to chew the case hardening of the gears after about a dozen runs.

/quote]

Our shot peening and Isotropic super finishing would help this situation.

The Bogan Grand Master

The Bogan

Posted
Posted

I think the engine check light was set up for over boost warning, its been a while and I cannot remember exactly.

I remember the low oil pressure warning light would come on at idle which was fine as it was set fairly high, it is adjustable if you want set it higher or lower.

sime1 Collaborator

sime1

Posted
  • Author
Posted

I think the engine check light was set up for over boost warning, its been a while and I cannot remember exactly.

I remember the low oil pressure warning light would come on at idle which was fine as it was set fairly high, it is adjustable if you want set it higher or lower.

oh ok no problem I take it to unigroup tomorrow will check with them. I should easily crack a 10 next run.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • Kinkstaah
      My BMW E39 528i touring

      By Kinkstaah · Posted

      @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...