Jump to content
SAU Community

Recommended Posts

My 32 is painted gold (bought like that) and it looks like a good paint job, other than they didn't tape it up very good. (A lot of spray) Whoever looked after the paintwork did a really bad job... If it ever was looked after. I'm using it as my test to cut & polish, but will be going through a couple of YouTube vids so I'm not completely hopeless. I'll chuck some before & after pics WHEN I do the deed. Only doing this because I will be getting a respray in the future.. Still tossing up between a darker gold or white..

Unfortunately this happens a lot where people just take a cut and polish to fix any paint issue and it ends up ruining your paint. Hope all goes well because sometimes a cut and polish is a must and seal with wax. If you get to that stage expect to wax it every 2 weeks or so.

Unfortunately this happens a lot where people just take a cut and polish to fix any paint issue and it ends up ruining your paint. Hope all goes well because sometimes a cut and polish is a must and seal with wax. If you get to that stage expect to wax it every 2 weeks or so.

Haha, yeah.. I'm pretty sure I will end up making it look worse :P

But, half of the paint has already been ground away to get rid of the rust :D

The issue with most detailing places is the firs thing they do is take a mild cut and polish to your car. RUINS your paint.

...or I recommend taking the time out and doing it yourself.

My detailer has a "Paint Thickness Gauge" which tells several stories - before even touching the car.

* How much paint he has to work with - or with the N1, not to work with.

* With sun damaged panels (horizontal ones), more latitude can be had with cut 'n polish within certain micron tolerances

* Panels which have been repainted will give off thicker readings

* Nicki (- sounds better than bog) can be detected in vulnerable spots

My detailer has a "Paint Thickness Gauge" which tells several stories - before even touching the car.

* How much paint he has to work with - or with the N1, not to work with.

* With sun damaged panels (horizontal ones), more latitude can be had with cut 'n polish within certain micron tolerances

* Panels which have been repainted will give off thicker readings

* Nicki (- sounds better than bog) can be detected in vulnerable spots

If you don't mind giving a ballpark figure, how much does it cost for someone to give the car that much attention to detail etc? Just curious really.

Eugene Chan charged me $400 (mates rates) for the two day weekend Jeremy.

EugeneDetail14.jpg

EugeneDetail6.jpg

EugeneDetail7.jpg

EugeneDetail13.jpg

EugeneDetail16.jpg

EugeneDetail22.jpg

Typical process was...

Wash > Clay Bar using Lubricant > Polish (Menzerna brand) 2x with different grade pads > Sealant (Optima brand) applied > Cure overnight > Wax (Meguiar's or Menzerna brand) > Buff

Eugene (aka JDM_Performance here on SAU) learned from Polich Doc in Melbourne. Eugene detailed my 3x R34 GT-Rs

#1 R34 GT-R Black won the Concours Skaife award at the R34 GT-R 10th Anniv

#2 R34 GT-R Bayside Blue (above) wasn't owned for very long before being forced to choose, upon the availability of an N1 - paint thickness on every panel was about 320 microns

#3 R34 GT-R White N1 in PI Magazine #161 - paint thickness on every panel was consistently about 90 microns

Yup, very happy with Eugene - but pretty far away from you guys I'm afraid.

  • Like 1

Yes it's impressive.

It won't work unless the panel is made of metal.

C/F, Nicki or rust with give lousy readings.

The Detailer has to love what he does - with a passion!

Eugene has that passion - yet he hates gardening.

I love gardening - but but hate detailing unless I'm totally in the mood and begin by 7am , Lol

Yes it's impressive.

It won't work unless the panel is made of metal.

C/F, Nicki or rust with give lousy readings.

The Detailer has to love what he does - with a passion!

Eugene has that passion - yet he hates gardening.

I love gardening - but but hate detailing unless I'm totally in the mood and begin by 7am , Lol

Thanks for the info Terry. Amazing job done on an amazing car. It's almost worth driving down to Sydney and then glad wrapping it for the trip home haha :P

If you let him detail your N1, then Eugene must be good.

Cheers for sharing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to it's full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so damn hot in there, that made it all the more easy to remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. I was standing there looking at the car and said 'f**k it'. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...