Jump to content
SAU Community

Recommended Posts

I put 34 GTR seats in my 32 GTR. The 32 seats are way to narrow in the shoulders for me. Suggest you sit in a 34 GTR seat before you buy it/them, since they're not cheap and you want to know they feel right for your body before you throw the coins. Bolt straight it - easy job.

  • 2 months later...

Hey guys, I can't have acces to BNR34 seat because they are not allowed in my state. However, from picture, it appears the shoulder and lower curves more than R32 meaning it should hug more but then some peoples suggest that the R34 is wider so actually the r32 hug tighter ??

Thanks guys :)

Im going to be different to everyone elses posts.... The 34 seats are of course much more comfortable and being so much newer in better nick in general.

But i have had 32, 33 and 34 gtr seats and none hug me at all. im 6 foot 2 and skinny.

If your upgrading because you think they hug alot more i dont think its worth it, but if your going for comfort, looks and condition, defiantly worth it

  • 4 weeks later...
  • 3 years later...

Reviving for my two cents.  I'm a fairly fit and thin dude.  I was thinking about getting the R34 seats for my R32 just to get something newer and in better condition.  However, after sitting in them, I couldn't bring myself to do it.  They feel like regular run of the mill seats where as the R32 seats hug a lot more.  Nothing compared to a racing spec seat, but still way better, in my opinion, than the newer seats.  

It sucks because now I have to figure out what seats to get.  >.<

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...