Jump to content
SAU Community

Recommended Posts

  • 2 months later...

When the AWD glide was still in my car I was able to run 10.4 not using the transbrake with a real lazy footbraked 1.7 60ft launch. Tried the transbrake few times and it just spun as I didn't warm up the rear tyres in my 33GTR.

Powerglide puts the power down so smoothly compared to a manual. Defienatley had a high 9sec pass with a decent launch. Power plant was a Rb26 with hks 2530's with a manual normally make about 600awhp.

  • Like 1

When the AWD glide was still in my car I was able to run 10.4 not using the transbrake with a real lazy footbraked 1.7 60ft launch. Tried the transbrake few times and it just spun as I didn't warm up the rear tyres in my 33GTR.

Powerglide puts the power down so smoothly compared to a manual. Defienatley had a high 9sec pass with a decent launch. Power plant was a Rb26 with hks 2530's with a manual normally make about 600awhp.

Did you change back to the manual??? What happened to the box?

  • 9 months later...

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

And GTRPSI my phone app didn't let me see you post

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

Add to that 5k for the box these parts that you will require also.

Custom length and spline output shaft to suit transfercase.

Fabricated sump to clear the drive shaft when the box is massively rotated

Suitable length and angle pick tube to put the oil filter at the bottom of the new fabricated sump.

The dip stick takes some messing around to get it at a suitable height for when the gearbox is rotated.

Decent torque converter can be $1000-2000.

Shifter

Transcooler ect ect

Pretty quickly it gets to 10-12K.

  • Like 1

Add to that 5k for the box these parts that you will require also.

Custom length and spline output shaft to suit transfercase.

Fabricated sump to clear the drive shaft when the box is massively rotated

Suitable length and angle pick tube to put the oil filter at the bottom of the new fabricated sump.

The dip stick takes some messing around to get it at a suitable height for when the gearbox is rotated.

Decent torque converter can be $1000-2000.

Shifter

Transcooler ect ect

Pretty quickly it gets to 10-12K.

Exactly, and thats assuming you know what your doing......

http://shop.quaife.co.uk/nissan-skyline-gtr-6-speed-sequential-gearbox

Chuck this beast in! Perfect daily/quarter mile monster.

Rated for a lousy 750 hp. Waste of time for a "drag car".

@Ryan, have you thought about selling the output shafts and other bits as kits for GTR owners?

That way we could build up our own strengthened autos and just add the bits on to convert them to work with the GTR transfer case.

Would save everyone a shit load of development and you could recoupe some of your already made developement costs along the way.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...