Jump to content
SAU Community

Recommended Posts

My 600's hit around 60% duty cycle under full load. They'll be pushing it on e85 IMO.

If I stayed with pump 98 and had chosen a different turbo I have not doubts that I could see much more power with these injectors..

I'll do some research into the 3076r, it looks like a monster..

Cheers :cheers:

I think these days Garretts GT3067R sounds like a good idea for a streeter that isn't too wild . It gets you into a GT30 that fits with the usual pipes and hoses possibly minus the spacer . On paper they're nocking on the 300 RWKW door and supposed to be responsive with a bit less exhaust restriction . Their only downside compared to a GTRS is they need the GT30IW dump flange and a non std suction/inlet pipe .

My gut feeling is that you can probably get 270-280 RWKW out of these on 98 ULP so the eth and consumption issues you can forget .

Tao as said may be able to do something similar as well .

IMO the right turbo is better than E85 in the long run for good all round usable street power meaning increased mid range that retains acceptable part throttle performance .

A .

Cheers discopotato,

Honestly I haven't read much about the GT3067R and I'm wondering why I didn't go that route when I chose the GTRS.

E85 in Brisbane isn't exactly everywhere so I might save the pennies and look down a different turbo road.

Thanks everyone for the replies, it has given me a lot to think about.

:cheers:

I went to my GTRS because it's an easy conversion and not a bad replacement for the std ceramic RB25 OE turbo .

I'd really like to see a GTX3067R back to back with a GT2835 Pro S but that's not likely to happen .

The economic reality is that the HKS turbo kit possibly isn't made anymore and was an expensive if complete set of bits . A GTX3067R would be cheaper new and allows an easy upgrade path to other GT30 based Garrett turbos if required .

A .

600 CC would probably be a bit small to keep decent AFR's on your set up. I've got 1000cc and use 80% duty at 306kw 20psi on a HG highflow. that was with wheelspin from 5k+ RPM so we don't really know how much power is being made. anyway I think they are probably similarly sized turbos and 600CC injectors might only get you there with an adjustable FPR and a very good fuel pump

Why was it wheel spinning on a dyno with only 306 kw?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...