Jump to content
SAU Community

Recommended Posts

Anytime I look for diff info, the same came up : 1.5way good for daily and time attack.. 2way are SH*T, only good for drift.


BUUUUTTTT... I was thinking about it... if 2way diff are so bad, then why did the BNR32 ( not sure about the others) came with 2way oem ?

Honestly, I never felt my car dangerous to drive/handle... or is that because my diff is worn and not really acting like a true 2way diff ?

As you can imagine, I'm on the hunt for a rear differential and was wondering if I could simply buy a 2way instead of sticking to 1.5way ( which are rarer to come by on the used market)

It's because 2-way and 1.5-way describes diffs in about the same way that "Stage 2" describes a cam. It's not enough information.

The definition of a 2-way diff is that it applies locking effect on both accel and decel. There is no component of the description that describes exactly how much locking effect is involved, except that it is approximately equal in both directions.

A 1.5-way diff simply provides less locking action under decel than a 2-way does. In this case the name implies a ratio of sorts between the two locking actions, but still doesn't say exactly how strong the locking action(s) is(are).

The factory R32 diff is a 2-way diff, sure. But who says it has the same degree of locking action that a tight-as-f**k aftermarket diff has?

I wouldn't use a 2-way (aftermarket) on a daily unless I absolutely needed it for some other part of that car's usage pattern, because they're not pleasant to live with. And also, unless you allow for it or drive aggressively to overcome it, the added understeer caused by a stiff 2-way diff can be not fun also.

1, 1.5 or 2 way is not really the issue in daily driving as said above, the issue is how "tight" or aggressively the diff locks.

a standard gtr diff is 2 way but not tight and you will never notice it as an issue in daily driving.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...