Jump to content
SAU Community

Recommended Posts

I was driving my track car last Friday and my engine all of sudden sounded like a wrx. I took all the spark plugs out to find one had cracked severely. I went down to supercheap and bought 6 new copper plugs (bcfr6es-11) and installed them.

It was hard to start and then once started a loud knocking noise was coming from the engine. So I turned the car off, checked fault codes for engine knock but none came up (5,5 on the ecu light).

I restarted the car and then unplugged each coilpack one at a time to see if the knocking stopped but the revs only decreased and so did the knock. I revved it up to 1500rpm and the knock got faster. Then after about 10 more seconds of idling the knocking stopped and the car stalled.

I then restarted the car again and it was struggling to stay on idle and sounded like it wanted to stall, and eventually it did.

I can post videos of the knock stopping and a video of after I restarted the car.

Please help. I have no idea where to start.

Spark plugs dont crack for no reason.

What is your tune like? I will guess and say something has gone wrong and engine has died.

The plugs cracking is an indication of Way too much heat (lean) so engine has pinged to death.

Do a comp test if you like. But the knock means it's dead anyway.

Mods are:

FMIC

Rb25 turbo

3 inch dump pump

Standard ECU

Compression test is:

Cylinder 1: 125psi

Cylinder 2: 121psi

Cylinder 3: 120psi

Cylinder 4: 125psi

Cylinder 5: 120psi

Cylinder 6: 126psi

Yeah but the car restarted after the knocking stopped. Also the car was running on 5 cylinders when putting it onto the trailer, and then immediately after the spark plug change there's a loud knock out of no where? I'm quite confused.

I just did another compression test. Cylinder 3 is giving different results.

Test 1 cylinder 3: 120psi

Test 2 cylinder 3: 80psi

Test 3 cylinder 3: 95psi

I'm assuming either what badgaz said, a stuck lifter or, a broken valve spring.

Valve spring would explain the knocking, missing and broad variance in compression results.

i'm pretty sure thats one of your lifters making a racket.... i fixed mine with pro-ma mbl8. i would try a good engine oil flush first, fill with some cheap thin oil...then run another flush...then fill with good oil mixing the l mbl8 with the last litre of oil.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...