Jump to content
SAU Community

Recommended Posts

Hey all - I've got the gtr tuned with nistune, however I'm looking at adding another high flow muffler to reduce some noise (and adding a cat converter) would I need to get it retuned? Does nistune retain some ability to alter settings on the go?

might be worth a quick power run to check if the new muffler and cat have caused some restriction and

need some timing taken out of the tune, but if the tune was not on the knife edge it will probably be

ok.

you shouldn't need to change the tune....but if you are a perfectionist you might.... restriction on the exhaust side can increase back pressure and increase cylinder temps,... i wouldn't worry so long as you aren't impeading flow.

depends on how much it impedes the flow...

I tuned my car with a completely f**ked pod filter and then when I put a new one on (same model exactly) we threw it on the dyno just for the hell of it and the afr's were out by 2

I change the muffler constantly on the road, as I use a Varex muffler. Going to a more restrictive muffler shouldn't change the tune that much, but any muffler that flows better will improve the airflow through the engine, possibly making it run leaner which is more of an issue.

If you are running petrol, running a little lean would be bad and possibly cause det. If you are tuned for ethanol, it would likely make bugger all difference.

I change the muffler constantly on the road, as I use a Varex muffler. Going to a more restrictive muffler shouldn't change the tune that much, but any muffler that flows better will improve the airflow through the engine, possibly making it run leaner which is more of an issue.

If you are running petrol, running a little lean would be bad and possibly cause det. If you are tuned for ethanol, it would likely make bugger all difference.

why would getting better flow out the exhaust cause a lean condition?

yes so if you turn your boost up then sure...but making an exhaust evacuate those burnt hydrocarbons better doesn't change those hydrocarbons....right....so yes it does mean you can add more fuel to your tune and make a bigger bang.

Less exhaust restriction makes it easier to get the exhaust out, making the manifold pressure lower, meaning more boost and better engine flow with no other changes.

If your AFM was out of resolution then it would definitely run lean, as there are no higher cells tuned to add fuel. I would be getting a retune just to make sure. There can be a huge change in engine flow due to simple exhaust changes. Other reasons for running lean could include running out of fuel flow for the extra airflow, even if the tune is compensated.

ok...my brain hurts lol...i don't think i was relating the pressure drop across the cylinder head i was treating it as intake vs exhaust and not really understanding the direct relationship....i understand now thanks :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...