Jump to content
SAU Community

Recommended Posts

Is there a link to a detailed thread on the attessa system in the nm35s?

My thinking was its pretty much rwd untill the system senses traction being lost and activates the fwd.

After reading about the rpm diffrence between the break sensor mod while on the stop and go pedals, i wanted to check. Sure enough sat on about 2500rpm as suggested.

Though i did notice small tyre witness marks on the driveway, so tried again the next day with the "Sync" switched on and held it a little longer to be sure, again twin marks.

I would have though the attessa would have not allowed that to happen? Also, i have taken off quckly on loose gravel had had the back spin and step out slightly.

So any more info on the attessa side of things (other then wikkipedia) would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/447319-attessa-question/
Share on other sites

Is there a link to a detailed thread on the attessa system in the nm35s?

My thinking was its pretty much rwd untill the system senses traction being lost and activates the fwd.

After reading about the rpm diffrence between the break sensor mod while on the stop and go pedals, i wanted to check. Sure enough sat on about 2500rpm as suggested.

Though i did notice small tyre witness marks on the driveway, so tried again the next day with the "Sync" switched on and held it a little longer to be sure, again twin marks.

I would have though the attessa would have not allowed that to happen? Also, i have taken off quckly on loose gravel had had the back spin and step out slightly.

So any more info on the attessa side of things (other then wikkipedia) would be greatly appreciated.

If you saw two black lines that would be different. Atessa reaction is not immediate. In fact R32 was quite slow. R33 (and Stagea) is quicker and R34 GTR is quicker still. The answer is in your second sentence - attessa senses traction being lost - it can't somehow anticipate it.

If you saw two black lines that would be different. Atessa reaction is not immediate. In fact R32 was quite slow. R33 (and Stagea) is quicker and R34 GTR is quicker still. The answer is in your second sentence - attessa senses traction being lost - it can't somehow anticipate it.

It does sort of anticipate it, by pushing some drive to the front wheels under hard acceleration, even if there is no slip. The biggest problem with the R32 setup is that its biased much too heavily to the rear. I have a cheapo ebay attessa tweaker in the GTR and it transforms the car. Also R32s also have no preload - ie no drive at all to the front under normal conditions. The R33 and later all send a little drive to the front all the time, which improves response, and is why you need to remove the front driveshaft if you're using a 2WD dyno. In an R32 you can just pull a fuse to use a 2WD dyno.

While we're talking attessa, do NM35s still require flatbed for towing like early attessas?

If you saw two black lines that would be different. Atessa reaction is not immediate. In fact R32 was quite slow. R33 (and Stagea) is quicker and R34 GTR is quicker still. The answer is in your second sentence - attessa senses traction being lost - it can't somehow anticipate it.

It does sort of anticipate it, by pushing some drive to the front wheels under hard acceleration, even if there is no slip. The biggest problem with the R32 setup is that its biased much too heavily to the rear. I have a cheapo ebay attessa tweaker in the GTR and it transforms the car. Also R32s also have no preload - ie no drive at all to the front under normal conditions. The R33 and later all send a little drive to the front all the time, which improves response, and is why you need to remove the front driveshaft if you're using a 2WD dyno. In an R32 you can just pull a fuse to use a 2WD dyno.

While we're talking attessa, do NM35s still require flatbed for towing like early attessas?

I have only ever flatbed towed the car. I wouldn't want to try due to the preload on the transfer case clutch though

I have a feeling the M35 electronic G sensor and Attessa computer is much quicker to respond than the earlier units.

So its more of a case of pecentage of power Vs breaking effect?

If theres a constant percentage of drive being sent to the front and you stand on the break and accelerator, is it just the fact that theres less power and larger breaks up front that allow the rears to turn?

My car breaks traction when my tyres are really cold or when the steep driveway is really wet or the combination and I cannot get up my driveway as the rear wheel is still spinning and I slide back down. This is at a low speed lets say 5km/h? Even with snow mode activated it struggles going up my driveway.

I can launch my car from 3500 or 2500? pissing down rain with the road flooding and not break traction.

My car also leaves chirp like marks when leaving my garage.

But, if going up a steep hill while raining and I floor it, I can feel the rear slip then the car straightens up then I know that attessa has corrected the slip.

  • 2 months later...

FWIW, as well as difference in front vs rear wheel speed from the ABS sensors, and longitudinal G force, they also have a TPS input.

so yep, it's pretty damn good at guessing when you might loose traction.

bloody amazing system for something designed on this

Classic-Games-The-Age-of-DOS-IBM-PC.jpg

FWIW, as well as difference in front vs rear wheel speed from the ABS sensors, and longitudinal G force, they also have a TPS input.

so yep, it's pretty damn good at guessing when you might loose traction.

bloody amazing system for something designed on this

Classic-Games-The-Age-of-DOS-IBM-PC.jpg

Yeah, I've watched my torque split gauge throw drive to the front whilst cornering, and encountering a dip; no loss of traction felt, but it is impressive in it's pre-emptive nature.

A wet road would likely have seen a loss of traction in that combination of conditions.

I have not ran part numbers on the nm35 systems, but from the looks of it they run an r34 pump and clutch packs. The only way to confirm would be to look at the g sensor.

If it is R34 data and programming it takes TPS, G sensor, wheel speed and the map sensor. Calculates over a matrix and runs variable prime pressures.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...