Jump to content
SAU Community

Recommended Posts

So recently iv just done the 100k on my GT.

6 iridium bkr5eIV - 11.

6 splitfires

High flow air panel.

New timing belt.

New pulleys.

Oil and all that shabazz.

(no need for oil details)

Anyway I still have 10 days to decide to take back the k&n panel and replace.

I have been thinking recently about building a cold air intake from the front right side bumper and using a heat Sheild under the AFM. Exchange the panel for pod.

My only reasoning is I had a lot of fun working on her doing the above listed and don't want to stop so want a decent project.

And B have heard of noise changes. I would be loving to hear if a whistle (ish) noise is possible.

I know a lot of people say a standard high flow panel is enough. But if I'd work on a heat shield and a intake pipe all the way from the front right. I couldn't see it taking in a different temp of air from the original air intake under the bonnet catch.

Anyway cheers guys.

Be keen to hear from you all and if you have any tutorials you know of to post please do so.

Laany

Link to comment
https://www.sau.com.au/forums/topic/448093-pod-filter-debate/
Share on other sites

Hey mate, I got my hands on a apex super flow, the pod filter is supposed to decrease turbulence created by cheap pod filters, and somehow flows better air into the turbo.

I also grabbed a already made panel that stops "heat soak" meaning supposedly stops engine heat going through your pod filter and just draws in cold air.

also got a maf adapter.

Pod filter - $80 delivered

post-89929-0-11346800-1409465896_thumb.jpg

Panel - $80

post-89929-0-76662600-1409465918_thumb.jpg

Maf adapter - $12

post-89929-0-89585600-1409465931_thumb.jpg

And by stock filter what do you mean?

The original nissan filter. They are good.

Replacing the camshaft seals is very easy whe n you have the timing belt off. They typically leak pretty soon.

The inlet one is very easy to pick out, the exhaust one carefully screw a self tapper screw into it to get it out.

Don't they come standard with a CAI.

If yours doesn't have one then I would chase a standard one down and use a OEM filter.

Modifying a N/A to get some power is a futile effort unless you are willing to spend 10's of thousands of dollars to get 100kw of extra power.

You can make it sound better with a pod, it may either make the same power, or, most likely less power though.

Its all basic science and physics.

Take the K+N back, they are illegal these days for a few reasons, the main one being they cover the AFM in oil causing them to miscalculate the airflow.

Pod filters are crap, they suck hot air from the engine bay unless they are in a perfectly designed and sealed CAI, It would cost you plenty of coin to even get close to matching the efficiency of the stock airbox.

I have seen the standard sized Nissan panel and airbox flow 500kw so the intake is not your problem. ^^ Listen to Bob, tyres, suspension and brakes would actually make you faster and safer.

Take the K+N back, they are illegal these days for a few reasons, the main one being they cover the AFM in oil causing them to miscalculate the airflow.

I'm inclined to disagree. I have had a K&N panel filter in my R33 for around 7 years and I am yet to have any issues with my AFM, the biggest issue I have is that the filter cleaning solution plays havoc with my skin so I need to wear gloves when cleaning my filter. In this time I have also have plenty of police look at the K&N sticker on my air box and not one has made a comment regarding it. K&N (obviously) stand behind their product and it shows as they appear to have done plenty of testing to show that K&N filter oil does not contaminate AFM sensors which can be read here

On the flip side, I think there are very limited performance gains to be had with a K&N (or any aftermarket) filter. I find the K&N item is preferable as I can take it out, clean it, re-oil it and slap it back in without having to go and get a new filter.

tl;dr

My message to the OP; no filter in existence is going to give you the whistle you are looking for. A pod filter may give you a bit of an induction noise but that's about it.

As for a cold air intake, watch this video and make up your own mind

Some dude in USA did some testing with air filters. Found that (surprise surprise) oiled filters weren't that great. Sponge filters (e.g. HKS) were shit. Best was Apexi paper but they are really expensive.

What's the cost of a K&N + oil/cleaners vs. $15 a year for a Ryco or Nissan paper filter? What are the gains and how much filtration do you lose? Those are the questions you should be asking yourself.

I rather have a paper filter that I can throw away than have a filter that I essentially keep rinsing.

OP, try a UniFilter (a.k.a. sponge on a funnel). I had one on my GTS-t when I first got it, it was loud as fark and filtered nothing smaller than leaves and pebbles. You might get a hissing noise on an N/A.

You also have this option:

40820d1111028860-fs-arospeed-coldfront-i

I have a n/a though man so taking that into consideration does it all still work the same.

when I bought my GTS (R33 N/A) it had a pod filter on it. Didn't make one ounce of different noise than the stock box. I changed it back to the stock airbox as pod filters are just shitty hot air intakes asking for a defect on an N/A.

when I bought my GTS (R33 N/A) it had a pod filter on it. Didn't make one ounce of different noise than the stock box. I changed it back to the stock airbox as pod filters are just shitty hot air intakes asking for a defect on an N/A.

That's what I was waiting for. Cheers man. Haha. Someone who's actually had it.

Thanks everyone.

Gonna just do a paint job and sell and get something else.

In East of Melbourne in Yarra Valley if anyone would know of anyone interested. Probably between 12-15k. Got 130 on clock.

post-135457-1409648332629_thumb.jpg

  • Like 1

not sure if you have one already but a nice cat back exhaust on an N/A really is a wonderful sound. Also a job you can do yourself and cheaply too if you pick up the cat back 2nd hand.

Don't be tempted to go for a GT-T cat back though as the turbo exhaust are too open and loud for N/As. It will drone...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...