Jump to content
SAU Community

S A U - N S W Spring Tech Arvo Saturday 8Th Nov 1Pm


Recommended Posts

SAU.NSW officially thanks Andy Spira of MotorActive and Peter O’Connor of DBA for hosting this wonderful event about lubricants and brakes


Topic: Liqui Moly Oils and Additives, and DBA Brakes


Day/Date: Saturday 8th November 2014


Time: From 1pm to approx 4pm


Address: MotorActive, Unit 35, Slough Business Park, Holker St, Silverwater




Parking: There is plenty of parking available


Food and Drink: Snacks and drinks will be provided


Cost is Free for Members - although non-members still have time to apply and pay


Limit of members who can attend is: 40, with a minimum of 20.


This tech arvo is going to be in two parts. One part will be on lubricants and additives including their effectiveness for both road and race applications. The second part will be with DBA on performance brake rotors, their make up, and how they perform in both road and race applications. Should be a very informative afternoon!


*** All advice and demonstrations given by workshops, professional practices and factories for SAU.NSW Tech Nights are the responsibility (of accuracy) of the establishments - not the car club.

post-91912-0-80225100-1410343305_thumb.png

  • Like 1

Attendees:
1). MrFijiGold
2). Terry_GT-R34
3). Victory
4). Clinton
5). Pezhead
6). Edifier
7). Redline_GTR
8). sammi_d
9). crashdown
10). stagea pete
11). levinboy
12). Aggroman
13). luke gtr
14). Rob260
15). RiseofBrutality
16). kila32
17). MrStabby
18). God_speed
19). MR33YO
20). GOD12A
21). Daleo
22). Aqua
23). peterj
24). Liz
25). Watchamacallit
26). benm
27). JoelyMoley
28). nick_7g
29). GoldZilla
30). 533 RYC
31). vorse
32). ls128
33). klebestift
34).
35).
36).
37).
38).
39).
40). DekA

  • Like 1



  • Similar Content

  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...