Jump to content
SAU Community

What Power Level Before New Head Gasket

Badgaz

By Badgaz,
in Engines & Forced Induction

 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

What cylinder pressure do the stock bolts stretch is what you would like to know, but there is no common way to check that while tuning. It would also depend what heat stress the engine was under I imagine. Manufacturers use the stock bolts as a fuse, to let the head lift rather than have a catastrophic bottom end failure when something goes wrong.

I had an MLS gasket let go on the VQ when my wastegate line accidentally popped off. I drove it like that for a year, not knowing what the issue was, just slowly pumping bubbles into the cooling system. It wasn't until I was on the dyno that the head lifted and the weep turned into a mess. Engine out for L19's and a pair of OEM gaskets.

I would say 350kw is around the stock RB's head gasket limits with the stock bolts, but it would depend on fuel and timing. Not saying you can't push through that, you are just living on the edge imo. Some say you can drop new ARP's in without even taking the head off, perhaps it's an option for you?

Badgaz Experienced

Badgaz

Posted
  • Author
Posted

I'd heard different opinion which said factory bolts were less prone to stretch than some aftermarket ones..... Either way it will be tuned to it's next limiting factor. We'll see how far she will go.

Ben C34 Grand Master

Ben C34

Posted
Posted

There's a dude running 600 kw or something nuts with a stock unopened neo with arp studs (replaced with the head still on)

I wouldn't worry about the gasket just blowing due to a certain power level. It's cylinder pressure that does it, and pinging shoots cylinder pressure through the roof.

  • Like 1
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Walbro E85 pump, they're quiet and seem to be pretty reliable.

One of my mates have had his DW300 fail but another one still has one going strong. Mind you both bought the DW pump before the Walbro E85 450L pump was available.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Duncan
      Chris' Toyota Mark ii JZX110

      By Duncan · Posted

      Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...