Jump to content
SAU Community

Preperation Required Rb30 Block For 3.2 Stroker Build

Nismo 3.2ish

By Nismo 3.2ish,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 501
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Nismo 3.2ish
Nismo 3.2ish

Just did a great big post and lost the farker SO Got the car, it is great. Only run in tune, limited to 5000rpm but feels very linear, cannot wait to get the final tune. The Coppermix C Spec clutc

r32-25t
r32-25t

Those people are idiots

Nismo 3.2ish
Nismo 3.2ish

Well a few things have been done, VERY SLOWLY But I have a few years left(I hope) so who knows, might get it sometime this Year, pics are all over the place but who gives a shit, lol I want my FN ca

Posted Images

Piggaz Grand Master

Piggaz

Posted
Posted

Thanks Mate, whats another 5 months, might change it back to a 26 while I still have the parts:)

YOU WILL NOT!!!!!!!!!!!!

when a 26 comes out it gets ground up and melted down then out to a better use, like a door stop or paper weight!

  • Like 1
Nismo 3.2ish Grand Master

Nismo 3.2ish

Posted
  • Author
Posted

Just did a great big post and lost the farker :(

SO

Got the car, it is great. Only run in tune, limited to 5000rpm but feels very linear, cannot wait to get the final tune.

The Coppermix C Spec clutch is fantastic and for a clutch that can hold 700HP it is like a normal clutch to drive.

The drivetrain seems smooth but need to really try a bit harder to get a better idea?

So it will be interesting to see how it drives after the final tune, I will post results when it is done..

It is a different car to drive. :wub:

Thanks to all of the blokes on SAU that helped me :worship: :worship: :worship: :worship: :worship:

  • Like 3
Nismo 3.2ish Grand Master

Nismo 3.2ish

Posted
  • Author
Posted

I think they were impressed with the results at CRD and they are looking forward to the final tune as well.

They had "JUN" there when I got there and that is a wicked machine, going to get into the 7s on streets soon :)

I have the same bottom end ============ and thats where it ends ,haha

Fuel was better on the way home than when I drove it in for the work ?

If today was anything to judge from, I think when mine is finished it will be a very good DD :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...