Jump to content
SAU Community

Recommended Posts

So it is in... I'm going to have to have a little fiddle with the sway bay. Looks like it needs lowered a smidgen the give a little more clearance for the sump pump.

Power steering hoses need relocating a little as will the header tank.

It all sits nice and low. Looks like I will be able to run the strut brace still.

post-15176-14217429190155_thumb.jpg

post-15176-14217432175935_thumb.jpg

looking good and enjoying the build :)

When someone is actually doing the work it makes it interesting to follow, mine is boring , no hands on or attention to detail..

Edited by Nismo 3.2ish

The coilovers are an old old set of tiens for r33 gtr. There way too short in the front, wound up for maximum front ride height, but they still bottom out. The rear ones are good on length. The spring rates are a little hard to calculate because there conical. The best I could work out they are around 12kg/mm front and 9kg/mm rear. The sway bars are also an ancient cmr set from a front and rear cut I came across 10 years ago. The rear cradle has had the squat angle and roll centures changed. The diff is solid mounted at the rear with a change to the pinion angle too. Adjustable camber arms etc as well. The front has seen a change of roll centure, camber adjustments through the adjustable lca, adj castor arms, off set stearing brackets on the rack to fix a bump steer issue that was a result of the rc change also allows acaman adjustments. Brakes are std calipers with braided lines using Hawk HT10 pads and DBA 4000 rotors front and rear. Wheels are 17x9.5 +18 with Kumho V710 245/45/17 medium compound. That should about cover it.

Edited by Noddy

Thanks Noddy.

I changed my rear hubs to R34 GTR ones so I could accommodate the GTR suspension also. I have a std set of R34 GTR suspension in it at the moment to get some measurements and it is way low in the front. I was talking to MCA about it and they gave me a few measurement points so they could supply some red shocks to suit.

Good to see you have plenty of speed with that set up.

Thank you.

Lol, you reminded me that mine has a 32 GTR diff axels and hubs. It is a hoot to drive, esp when im chasing down other skylines or zeds. I have found plenty of mechanical grip in mine. Come visit 1 day, I'll show you what I have found over the years.

The coilovers are an old old set of tiens for r33 gtr. There way too short in the front, wound up for maximum front ride height, but they still bottom out. The rear ones are good on length. The spring rates are a little hard to calculate because there conical. The best I could work out they are around 12kg/mm front and 9kg/mm rear. The sway bars are also an ancient cmr set from a front and rear cut I came across 10 years ago. The rear cradle has had the squat angle and roll centures changed. The diff is solid mounted at the rear with a change to the pinion angle too. Adjustable camber arms etc as well. The front has seen a change of roll centure, camber adjustments through the adjustable lca, adj castor arms, off set stearing brackets on the rack to fix a bump steer issue that was a result of the rc change also allows acaman adjustments. Brakes are std calipers with braided lines using Hawk HT10 pads and DBA 4000 rotors front and rear. Wheels are 17x9.5 +18 with Kumho V710 245/45/17 medium compound. That should about cover it.

We also converted to R33 GTR shocks in our R33 GTS-T because of the greater range of shocks available for GTR's. We settled for Bilstein PSS9's as they can be serviced and re-valved locally.

In the front end we had similar problems with overall the shock length being too short as GTR shocks are 50 mm shorter than GTS-Ts, so we copied what the 4WD guys do and fabricated spacers to go between the top of the shock and the mounting point. This was a simple way to extend the overall shock length.

post-24210-0-70480900-1422013826_thumb.jpg

post-24210-0-18357600-1422013809_thumb.jpg

In the rear end we installed a complete R33 GTR rear cradle.

post-24210-0-28913400-1422013792_thumb.jpg

In hindsight one improvement to the alloy spacers would have been to use helicoil insets for the threads as the alloy is soft and you have to be careful not to damage the threads.

For ease of change over we came by a complete GTR cradle which we then refurbished with all new bushes etc. and then just did a straight swap. The benefit was a good diff, stronger axles, more bracing in the cradle, alloy hubs and the capacity to run GTR shocks.

I had a new set of GTR sub frame bushes in the parts box so we installed them at the same time. As you can see from the above picture GTR bushes are longer and have the effect of spacing the entire cradle 20 mm lower than GTS-T bushes. The impact of this is something that we did not realise at the time.

We are not using pineapples and I am still getting my head around calculating roll centre and the impact of ride height on roll centre. We run standard arms on all of our cars and obtain adjustment with adjustable bushes. We started off with a ride height of 330 mm and had a range of power down issues with that set up. We run our other GTS-Ts at 350 mm and they seem to work well and our GTR sits at 370 mm. The other issue we had was a lot of squat in power down to the point that at WSID the outside 5 cm of tyre was not even being used.

With this information we raised the rear ride height to 370 mm and reduced the rear camber to -1.00 degree. We also softened up the rear end by going down to a 5 kg springs. The result of these changes has been much better power down, mid corner stability and the ability to keep wheels on the ground when the surface is not perfectly smooth.

What we probably should do is have the car corner weighted by Heismans in Sydney who can also work out where we are regarding roll centres. Any advice that you could provide would also be very appreciated.

  • Like 1

I have used an r32 GTR subframe complete with diff, axels, hubs etc. In stead of replacing the bushes I cut them down. 1mm cutting blade, removing all the rubber away level with the top of the cradle. I made 4 washers with an exturnal dia matching the cradle, the inner hole for a neat fit over the tube the body pin slides through and partedthem off 2mm thick. After stich welding the outer edges I cut the tube off flush with the top of the washer and weldedi it in too. Effectively I've solid mounted it to the body so it has been raised up as far as possible. This helps to keep the rear geometry roughly in the same position whilst lowering the body and center of gravity. It also keeps the roll centure happy.

The rear bushes for the diff were pretty sad in it too. So, we measured very carefully and cut the whole section out and replaced it with 4mm plate. 3 sets of holes were drilled, first in the std location, and then 20mm above and below. Looking for better grip and drive from the rear we looked to some drag racing concepts like pinion angle. Kinda made a difference.

The most drematic improvement for drive out of corners came from playing around with the squat angle of the cradle. Spacing the front of the cradle down about 12mm was fantastic. 20mm should be better right... nope it started to get messy under brakes in the rear.

Up front I've remade the lca with rose joints for camber and track adjustments and moved the mounting point up higher in the cross member to match the changes in the rear. In actual fact, I developed the front first because it was suffering lots of mid corner and exit understeer. Thats when I started looking very closely at geometry and bump steer etc.

Fixing the rc in the front accidentally created lots of bump steer. So I made an offset extension for the steering rack to put the tie rods back is the same alignment as the lca. Bump steer fixed and almost 0 accerman at the same time.

I find I can carry a lot more apex speed which has helped me to keep up with more powerful cars. Turns in and keeps on turning throughout a corner. The rear end puts power down as well as anything I know of and drives off the corners. No more axel tramp.

Corner weighting is another story. Done properly it makes the ballance so much better, especially the weight transfer side to side more than front to back.

Edited by Noddy
  • 2 weeks later...
  • 10 months later...

I kind of just fell off the face of the planet just there didn't I...

My year got very busy with a wedding, repairing the levin, honeymoon and house renovations, all have stolen time away from my beloved skyline. the sadest part of all is that I am going to have to move to toowoomba this year and most likely to a smaller shed. I think I might have to part the old girl out and sell it off.

Edited by Noddy

It happens to the best of us, life rears its ugly head and gets in the way of our passions!. Stick with it mate, the desire always returns eventually!

Mine has been in bits for 3 years and my motivation has only just come flooding back now.

All the best with it.

I kind of just fell off the face of the planet just there didn't I...

My year got very busy with a wedding, repairing the levin, honeymoon and house renovations, all have stolen time away from my beloved skyline. the sadest part of all is that I am going to have to move to toowoomba this year and most likely to a smaller shed. I think I might have to part the old girl out and sell it off.

If you can afford to ans have the space, buy a shipping container. The car will fit in it and its like a lock up garage.

You can get them starting from around $1,000 if you have contacts, $2500 and upwards if you don't.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...