Jump to content
SAU Community

Breaking Rear Drive Sharfts

r34unit
 Share

Recommended Posts

r34unit Rising Star

r34unit

Posted
Posted

yo
I was driving my mates r34 gtt today it has 330 kw blah blah, with a heavy duty clutch and standard drive train.
As i hit boost in second gear it broke the passenger side rear drive shaft. This is the second time its happen on the same side. The drive shaft has lasted two months tops since its been rebuilt.
as any one else had this problem ? does he maybe have a problem with his diff causing it to break on the same side ?

thanks in advance ?


Link to comment
https://www.sau.com.au/forums/topic/451743-breaking-rear-drive-sharfts/
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Just because it snapped coming on boost doesn't mean that's what killed it, the damage was done (not long) before the failure looking at the pics.

How hard does he drive it? Would take a massive shock loading to snap that shaft...

  • Like 1
89CAL Grand Master

89CAL

Posted
Posted

No, GTR are outright 6 bolt, plus stronger everything.

NA should be 2x3 6 bolters, like S chassis cars, with the weakest CVs. R32/3/4 turbos should be 5 bolt with the "medium" strength CVs.

I must be going crazy, Could have sworn when I was looking at driveshafts when I snapped mine the GTR ones were 3x2 but a quick search now it seems that they are 6x1. Going senile at age 25 it seems..... :S haha

When I snapped mine I figured it was from excessive axle tramp (the initial fracture) and a hard launch one day finished it off. It was a very similar failure to yours. This was on 195rwkw with 19" wheels and 265 wide rear tyres. I now have near 300rwkw and 18" wheels with 265 tyres and Havent had a driveshaft problem since the first one. Mind you I dont go dropping my clutch and doing skids

GTRPSI Mentor

GTRPSI

Posted
Posted

Any pot holes or rough road when it happened?

Saw a gearbox break recently due to this, going onto power, car got slightly light and back down again over the roughness killing the box.

Never had a issue on the flat in the past.

As could axel tramp.

  • 1 month later...
  • 3 years later...
ERO54N Community Regular

ERO54N

Posted
Posted
On 12/15/2014 at 5:55 PM, r34unit said:

post-99078-14186264603518_thumb.jpgpost-99078-14186264727933_thumb.jpgypost-99078-1418626504493_thumb.jpgpost-99078-14186265196841_thumb.jpg

Nice pics, very interesting break. I'm no expert but it looks like metal fatigue.

https://en.wikipedia.org/wiki/Fatigue_(material)#/media/File:Tender_fatigued_axle.JPG

If the replaced driveshaft was a used part a contributing factor could be that the unit was repeatedly loaded beyond its intended limit during its lifetime aswell. Similar to when you bend a paper clip at the same point until it eventually snaps.

Dark, corroded void near surface looks like it may also be a manufacturing defect but that's just assumption, could be just oil stain.

As to why coincidently passenger drive shaft failure may be to do with how the differential is transferring load, similar to how an open differential spins one tyre under certain conditions.

May only be far fetched and theoretical but hope this contributes to the discussion.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...