Jump to content
SAU Community

Recommended Posts

Car was dropped off yesterday to get the guards done should be finished by mid next week. Then car will be sent off for some more work at havoc fab and then off to racepace for some cusco suspension work.

Took a photo of it before I put it on the trailer. Still undecided if I should keep the wheels white or spray them black

post-84279-14374609586873_thumb.jpg

I'm going for pretty much exactly like this guard work front and back.

post-84279-14374610100597_thumb.jpg

If the flare job ends up as good as that blue thing you would have to be happy with that.

Stick with the white centre wheels. More work to keep clean but it will stand out more on the track and in your pics.

If the flare job ends up as good as that blue thing you would have to be happy with that.

Stick with the white centre wheels. More work to keep clean but it will stand out more on the track and in your pics.

Yeh those guards look awesome. I've shown the bloke doing the work this pic and said make it look exactly like this. Gunna cost me a bit but it will be worth it.

I'm with you on that I reckon the white stands out more to. It's defiantly gunna stand out on the track.

The rear end will be a comparatively easy.

Front end suggestion - get the ride height down near where you want it, crank on the camber and caster you will need, and with the springs removed from shocks get an idea of what rubs as you move the wheels through their suspension and steering range. Anything looking like rubbing needs some loving with a hammer to give clearance.

Yeah the car will be getting lowered as low as it can go once other side is done then they will be going through with all the clearances problems. I've told them I don't want any rubbing/fouling throughout the steering arch. They've taken a lot out of the guards because they haven't adjusted the height yet and those guards were sitting on the tyres.

Plenty of camber, none of this half-done 2.5 or 3 degrees stuff. Make sure your hardware allows for a good 5 degrees, then with clearance for that amount you'll never have troubles.

The forward tub sections will be the area needing some love, particularly with a bit of caster pulling the wheels forward.

I'm really looking forward to the end result.

Yeh as soon as this work is done I'm gunna send it in to racepace to get there modified cusco arms.

You and me both!! Car should be fully finished in the next 6 weeks.

What do racepace modify on their cusco arms?

Every arm in my 33 is cusco and Ive never run out of any adjustment, running modded knuckles and relatively extreme alignments.

Wondering if Ive missed something?

  • 4 weeks later...
  • 3 weeks later...

Cars in at racepace atm getting the work done. Slowly running out of time to get it ready for wtac [emoji45]

Keep at it dude. We just put the gearbox back in mine on the weekend.

Use the SAU Nats on the 3rd of Oct as the shakedown.

  • 4 weeks later...

Cars slowly coming along at the panel beaters should be finished by next week from getting the custom guards done. Fronts are done minus paint. Look awesome!!

post-84279-14435868508894_thumb.jpg

post-84279-14435868681896_thumb.jpg

post-84279-14435868805992_thumb.jpg

post-84279-14435868903861_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...