Jump to content
SAU Community

Recommended Posts

Looking to build or buy an exhaust that is super stealth and quiet but is non restrictive up to around 350kw. (no i do not want to go a varex muffler)
Currently running 3inch turbo down to cat then a 4inch kakimoto.
I was thinking from cat back run a 3inch exhaust with 2 mufflers ? any other ideas or sneaky stuff people have done ?

Link to comment
https://www.sau.com.au/forums/topic/453530-sleeper-exhaust-systems/
Share on other sites

What do you mean sneaky?

I ran a hooker aero chamber and a Berkeley straight through at the rear. Was under the legal vole by a fair bit, no drone and flowed over 300 rwkw.

Research exhaust design. Two mufflers the same don't do much more than one. Fit the biggest mufflers you can fit. Look at branch resonators if you have a particular frequency drone you want to cancel.

I tried a few combos until I was happy with the result.

  • Like 1

By sneaky I mean running a stock cat back exhaust then running a waste gate with a small pound spring to vent out exhaust gases. attachicon.gifImageUploadedBySAU Community1423175348.468724.jpg

Like so :) ^

very cheeky indeed, similar to how OEM cars get away with noise. If you crack open a stock EVO muffler it uses a little flapper to control noise when doodling around town.

I have the HKS silent hi power on my GT-t. Has a Hypergear SS2 turbo, custom 3' dump and front pipe and hi flow cat and its really quiet at idle. I can confirm that the nismo is quieter having been on a few cruises with Raj.

And I'm currently making 320.6 rwkw at 22psi on E85 so it doesn't appear to be too much of a restriction

plus one for the Nismo.... i put one the 3" version on a N/A skyline and it was still very quiet and sounded batter than any custom system i had heard before.... i was very suprised when we started and drove the car.

another option is like the exhaust i have i think its a fubijsbu its a twin 2.25 inch system with a single straight through muffler at the rear and 2 resonators, passed EPA and flowed 350kw

I got a full 3.5" turbo back exhaust with a custom oval 3.5" muffler and a custom AES 3.5" rear round muffler

Nice and quiet and doesn't drone, been pulled over for rbts and by random cops in the city and even asked to rev the car and they were happy with the volume

So far flows 450kw ample for your power

  • Like 1

If that thing had any mufflers in it in the first place!! They are both far too small to do anything. Replace the centre one with the biggest oval centre-centre muffler you can. Replace the rear one with the biggest muffler (probably oval again) you can. Instant fixup.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...