Jump to content
SAU Community

Recommended Posts

Hi all,

Doing a turbo install which led to all my coolant in the engine being drained out. How would I go about refilling this? I can't start the car and run it waiting for the thermostat to open as there's no coolant to heat up.

Would my best option be to remove the thermostat and just have a bit of straight hose connecting my radiator to the car?

If so

How would I go abouts putting the thermostat back in without covering myself in coolant and loosing a majority of it?

Thanks

Actually does the thermostat need to be open to refill the engine with coolant or will it still flow in the engine 1 way with it being shut? I thought that it wouldn't matter but my coolant bottle is still showing Max when I've drained the block which has just confused me. Help would be greatly appreciated !

Just pour coolant in like normal, most thermostats have a small air bleed hole.

When your warming up the car, the thermo will open, water level will drop and you add coolant.

Then follow the standard bleed procedure, open the bleed nipple when hot to purge out any air pockets in the head.

Should all be in the workshop manual.....

Dude i know you're new but come on, there's like 20,000 threads on draining/flushing coolant. Download workshop manual as above, its pretty straightfwd and you don't need to remove thermostat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...