Jump to content
SAU Community

Recommended Posts

My mechanic is having trouble figuring out where to trim the diff. The problem is the diff will fit int he case but it wont spin, it lock when the diff is in position so it must not make the good contact but he can't figure where it was to be removed because it's not knocking anywhere.

I found these information on the net but it doesn't seems to help me much.. can someone shed some light please ? and/or translate the instruction from nismo in japanese ?

I'm willing to pay for the information, we really need to get that pan installed so we can proceed with the rebuild.

Thanks !

http://www.gtrpwr.com/showthread.php?t=6675

Link to comment
https://www.sau.com.au/forums/topic/458239-how-to-install-front-nismo-diff/
Share on other sites

As in the gears are meshing way too tight and won't turn?

All diff either use shims or threaded adjusters to set pinion depth and pattern.

It shouldnt be that confusing.

Maybe this will help a bit. It shows the shim under the side bearing races etc.

http://www.gtrpwr.com/showthread.php?t=6675

Haha. I linked to your link. Too early for me.....

So it binds up when fully assembled? Is he experienced building diffs ?

what confuse him is that it appears the diff is not ''grinding/touching'' any of my housing ( like if my housing already had the material grinding before..) so he was like '' cool, bolt-on affair! '' but then when we started turning it, it would turn 3/4 and then jam.

What i do is an old school method but may work mate. I paint all the gears turn them and then remove all the gears to inspect the wear or contact pattern. I do that first with the original unit then compare it to what im looking for with the new one. It should be the shim method. This is the rear diff right. ??

Edited by MJTru

What i do is an old school method but may work mate. I paint all the gears turn them and then remove all the gears to inspect the wear or contact pattern. I do that first with the original unit then compare it to what im looking for with the new one. It should be the shim method. This is the rear diff right. ??

Title of the thread says its front diff.

HarrisRacing's build thread has pictures on where to grind material off the sump http://www.sau.com.au/forums/topic/447384-r32-gtr-build-in-usa/?p=7559306

Which is shown in the original post link.

Seriously.

Yes there are 5 places to grind.

4 of them allow the diff to be installed. (Mine simply would NOT go without these ground clear).

The 5th place needs to be relieved so the LSD can rotate. It is the boss for the bolt threads next to the oil pan side. I didn't grind this one enough in the pictures below and the next group of pictures didn't come out clear after I ground it later...but had the same exact issue your mechanic had. You'll see some marking and grinding in the pictures below...the bolt boss wasn't ground enough and the wider diameter of the new LSD wouldn't clear in 4 places of rotation. When you fit it, you can easily see clearance issue (as your mechanic did).

What...you don't have a japanese mechanic? The instructions were very clear (if you know Japanese!) :)

Make sure he gets his shims and preload right! The preload on this front diff is so low it's laughable (AND HARD TO GET RIGHT).

post-136202-0-63656800-1437391408_thumb.jpg

post-136202-0-12309300-1437391449_thumb.jpg

post-136202-0-30789000-1437391476_thumb.jpg

post-136202-0-51418000-1437391615_thumb.jpg

Edited by HarrisRacing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...