Jump to content
SAU Community

Recommended Posts

I take off from most lights to get in front of the traffic, but always look around for any hotted up / quick cars who will follow me and try a bit harder if there is.

Never past the speed limit, maybe 2-3km/h over...incidentally the amount of speedo correction tolerance the authorities allow for.

Better or worse than the flogs with alfa/lancia etc that have Itallian flags?

Prolly not as bad cause the only cars that can really upstage them are Ferraris

I feel like these German flag donning Volkswagen owners are under some delusion they belong to the BMW/Mercedes crowd of luxury marques

No one races me off the lights :(

My last one I almost slid into a c63 amg lel at calder ofcourse too.

DAM YOU ACHILLES!

nah but srs they aint so bad once you get some heat into them

Edited by UNR33L

The worst are people pulling out of a slip lane in front of you as soon as you've taken off from the lights. Had a taxi do that lastnight and had to change lanes...

Your car has a factory LSD Leigh? Need AD08Rs brah. If I owned your car and was into prinny runs I'd get a cheap set of wide 17s and put MTs on them, swap them over before you go out on Friday night haha.

that's just asking to get pulled over!

did just put a deposit on some BBS LM reps doe, now what tyres are decentish and cheap considering i'll probably burn through them anyway?

595 RSR don't do 19s and invos / NT05s pretty pricey.Thinking regular 595s because they come in 19s, although my GTR had them and they were pretty shitty on the track and tore up, maybe i'll just get Achilles again.

Edited by UNR33L

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...