Jump to content
SAU Community

Recommended Posts

3 minutes ago, emts said:

they look like calais stockies?

D.A.D. proper VIP brand.

or Moh, get these for the B, oh wait...

http://page14.auctions.yahoo.co.jp/jp/auction/s446480700

could have been you: 

12322846_10208157528721231_3232278332267

On 8/31/2016 at 11:04 AM, joeyjoejoejuniorshabadoo said:

Dissatisfied cause they couldn't afford the petrol to drive home from racepace



I can very confidently say half the time I'm working in the engine bay of a Skyline, half the time is spent fixing another workshops f**kups, the other half is actually doing the mod / maintenance.

only open 10" wide max... so you'd need 9" or smaller to even get it on. they need to make a stance version.

and would you comfortably attach it in a carpark or is it just for garage?

narrower tyres on the rear of the gloria, added some aftermarket toe eccentric bolts, then some Megan Racing rack-end's for the front. getting ready for #lowlyf #slammage #obey #bippu

tumblr_nwkg1qyQeL1re2ujro1_500.jpg

https://www.instagram.com/p/6Fo7Vxgseb/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...