Jump to content
SAU Community

N/a N14 Sss Pulsar

jazzaa22

By jazzaa22,
in Engines & Forced Induction

 Share

Recommended Posts

jazzaa22 Apprentice

jazzaa22

Posted
  • Author
Posted

i do plan on dropping a sr20det motor in it, in the middle of saving up for it now. so as Gus Baby said about brakes and suspension im looking into that now, whats a good set up in regards to brakes? Budget roughly $150 for front and same for the back, or around that. Cheers

Leroy Peterson Grand Master

Leroy Peterson

Posted
Posted

Nah, keep it N/A. SR20VE

Lots more f**king around than turbo and sometimes more expensive.

$150? On what? Brake pads?

If you're on a real tight budget (like 90% of all other pulsar people) yellowspeed coilovers are cheap and do a reasonable job. N15 SSS brake calipers are a bolt on upgrade (same as GTiR).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...