Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • 1 month later...

What did you put in it Kat?

And does it go.....  clunk de clunk de clunk?  I hate that.

Mine is the V-spec and from what I can see it's a pain to put a 'normal' diff back in but looks like I have no choice with what I do with the car.

Is there an option other than to a 1.5 now? Is there a tru-track available anyone?

12 hours ago, DJBarnstar said:

Does the Nismo 1.5 go clunk de clunk de clunk?

I personally have not done my diffs to confirm or deny, though that is what i will be doing. 

@Piggaz Should be able to answer that for you if he is nice enough....

12 hours ago, DJBarnstar said:

Does the Nismo 1.5 go clunk de clunk de clunk?

The GT PRO is quite cranky with the Nismo oil it comes with. I switched to the OSG 80W-250 and it shuts it up by 85%. This was with solid alloy diff bushes but I've ditched them and put some Nismo rubber bushes in. Haven't driven the car yet but it should be a lot better again.

  • Like 2

I think you can get quafe for the rear as well. It also might be worth checking that the fluid is topped up for the rear diff. Right side of  the boot from memory.

Or you could sell it back to me.... :P

  • Like 1
On ‎15‎/‎11‎/‎2016 at 5:10 PM, DJBarnstar said:

Does the Nismo 1.5 go clunk de clunk de clunk?

 

On ‎16‎/‎11‎/‎2016 at 5:41 AM, Piggaz said:

The GT PRO is quite cranky with the Nismo oil it comes with. I switched to the OSG 80W-250 and it shuts it up by 85%. This was with solid alloy diff bushes but I've ditched them and put some Nismo rubber bushes in. Haven't driven the car yet but it should be a lot better again.

Like Piggas says.  Diff goes clunkety clunk even on the lowest setting.  Change the oil and it becomes liveable.

  • Like 2
  • 4 weeks later...
1 hour ago, DJBarnstar said:

Should I try and swap the current Nismo end caps with someone for stock GT-R ones?

 

I'm leaning that way.

 

What do you think?

20161216_200529.jpg

20161216_200547.jpg

I have a brand new set in packaging if you wish to swap. A bit of money your way too.

And thanks for the lead Anfanee. 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...