Jump to content
SAU Community

Recommended Posts

Hi everyone,

Just a quick question about a series 1 rb25det..
was wondering if I'm able to replace my big end bearings with acl bearings to freshen up the bottom

end a bit, I havent spun a bearing or anything like that just wanting to make sure I have fresh bearings
before I go giving it a hard time. If so am I able to just get standard size acl bearings, check clearances

with plasti gauge and if all clearances seem okay whack it all back together?

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/460070-big-end-bearing-replacement/
Share on other sites

As above

unless you are planning moderate to heavy mods (and if you are you should be doing more then replacing just the bearings anyway), the OEM bearings will be fine. Unless you suspect a problem, and even then I'd only be pulling a few caps to check if i was really concerned

Theres nothing wrong with freshning up a motor if you know how, new bearings and rings are good to have but in saying that if the current motor is in good cond with good comp aslong as you have a good tune, change oil every track day theres no reason it wont last I still have my 25 drift car stock bottom end with 4years with no problem but I also have built a spare bottom end with new bearings and rings to have ready to go. Really up to you which way you want to go.

  • Like 1

Alright, Thanks for all the replies

I'm paranoid of engine failure.

I'm hoping to get a 25 long block shorty for that exact reason.

So if did oil control mods - head drain, block restrictors, machine

Oil return.. I should be a lot better off than just a standard 25?

Also does billet replacement oil pump gears help with the pump failure

Issues? Or is it more so to do with the collar?

Thanks again, really appreciate it.

I disagree. There is plenty of people out there who abuse the f**k out of their standard engines running Big boost for years and never smash an oil pump. Myself included. Something else always gives (general wear causing low compression and giving excessive blowby, or just bad luck like spitting a shim or melting a piston due to a fuel pump dying)

Personally I think the thing that kills oil pumps is the little silver and red badge on the car that says 'GTR'

  • Like 2

I disagree. There is plenty of people out there who abuse the f**k out of their standard engines running Big boost for years and never smash an oil pump. Myself included. Something else always gives (general wear causing low compression and giving excessive blowby, or just bad luck like spitting a shim or melting a piston due to a fuel pump dying)

Personally I think the thing that kills oil pumps is the little silver and red badge on the car that says 'GTR'

I melted a piston because my fuel line ruptured and she leaned out - I made the upgrade to an 2530... [emoji2]

I disagree. There is plenty of people out there who abuse the f**k out of their standard engines running Big boost for years and never smash an oil pump. Myself included. Something else always gives (general wear causing low compression and giving excessive blowby, or just bad luck like spitting a shim or melting a piston due to a fuel pump dying)

Personally I think the thing that kills oil pumps is the little silver and red badge on the car that says 'GTR'

I was tongue-in-cheek in both posts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...