Jump to content
SAU Community

Recommended Posts

If you take all the gears out, and the brake bands, and the clutches, and then the valve body, and the torque converter, and get rid of the bellhousing and the back half of the case, and replace all those bits with a 5 speed manual.....that'll just about do it.

  • Like 1

type your gearbox code into google and see what pop ups. i think the gtt is a re4r01b?

everything i have read has stated that anything that stops slippage is a good thing. on this reasoning alone, many 4x4 guys will run a higher pressure to alleviate slipping at low loads.

call a transmission expert tomorrow and have a chat to them and see what they recommend and their reasoning behind it.

I looked into this when I still had the auto in my GTT, most shops just scratch their head when you mention Tiptronic or RE4R0__ to them.

GTSBoy covered your main options above. MV Automatics in SA is typically one of the first recommendations when you want something done to these boxes. I also found something called a Keas shift kit with references to Knox Automatics in VIC, maybe check them out.

Also maybe check with Scotty NM35 and Kinkstaah here they're both running built autos.

The cost adds up pretty quickly and depending on how far you want to go you may want to consider a manual conversion instead. That's what I did.

The cost adds up pretty quickly and depending on how far you want to go you may want to consider a manual conversion instead. That's what I did.

^ This.

Although you have to remember, the auto is then built for decent power and every bearing and seal has been replaced, and the stall converter is matched to your turbo. If you wanted that sort of power through a manual you would need a decent twin plate clutch which can ruin the drivability, then you still have an old gearbox with worn bearings unless you get the manual rebuilt beforehand.

Buy my entire gearbox and flex plate and torque converter and PCS so I can buy a manual conversion.

Wouldn't even be mad, at this point... that's how much money you have to spend to get comparable to what comes standard in a skyline for $0.

Buy my entire gearbox and flex plate and torque converter and PCS so I can buy a manual conversion.

Wouldn't even be mad, at this point... that's how much money you have to spend to get comparable to what comes standard in a skyline for $0.

Something tells me the torque you are putting to the ground will smash a manual box in no time Greg, so factor in a PPG gearset also. :P

how did you go speaking to an automatic specialist yyc34gtt?

i called a really nice bloke who used to do re4's but has now moved onto amg's and bmw's. we had a long chat about different upgrades, line pressure, shift kits etc.

he said that the main thing that causes flaring and slipping in the automatics is the shift solenoids and or a worn valve body as they're aluminium.

I mentioned that my box was still quite tight, only flares once or twice in a 30minute session of hard driving, and i am planning on putting more power into it. What can and should i do? His answer, nothing. if it's still shifting fine now with more boost it sounds like its in good condition, if it does start to slip, buy new solenoids and possibly a new valve body and it should be fine. The thing he didn't like was upgrades such as line pressure, blocking off pistons (he called them something else) and the other 'usual' one off mods people do, as it puts a lot of strain on other components and will not last unless you do them all, and it costs more than doing the right thing, which is replacing worn parts.

^ This.

Although you have to remember, the auto is then built for decent power and every bearing and seal has been replaced, and the stall converter is matched to your turbo. If you wanted that sort of power through a manual you would need a decent twin plate clutch which can ruin the drivability, then you still have an old gearbox with worn bearings unless you get the manual rebuilt beforehand.

Totally agree, either option will add up.

The good thing about (re)building a gearbox is that you'll know what's in it, doing a manual conversion you're pretty much relying on the seller's word that it's in workable condition. I got lucky.

Re drivability, I ended up going with an NPC single plate organic that is very easy to drive on the street and has held up well @ 275rwkw.

how did you go speaking to an automatic specialist yyc34gtt?

i called a really nice bloke who used to do re4's but has now moved onto amg's and bmw's. we had a long chat about different upgrades, line pressure, shift kits etc.

he said that the main thing that causes flaring and slipping in the automatics is the shift solenoids and or a worn valve body as they're aluminium.

I mentioned that my box was still quite tight, only flares once or twice in a 30minute session of hard driving, and i am planning on putting more power into it. What can and should i do? His answer, nothing. if it's still shifting fine now with more boost it sounds like its in good condition, if it does start to slip, buy new solenoids and possibly a new valve body and it should be fine. The thing he didn't like was upgrades such as line pressure, blocking off pistons (he called them something else) and the other 'usual' one off mods people do, as it puts a lot of strain on other components and will not last unless you do them all, and it costs more than doing the right thing, which is replacing worn parts.

I have not yet spoken to any automactic specialist here in Calgary Canada, as there is not many that knows how to work on a skyline except 1 places but they sucks and they go only for money...

So far the Solenoid A and Lock UP solenoid needs to be replace on my car as they are done, I have contacted MV Auto and got a quote for the Solenoid A and B and Lock up. also the shift kit... I am in no rush at the moment as its winter here now and the car is parked...

do you mind asking your friend again for the exact parts for upgrading or replacing aside than the valve body and the solenoid? maybe the parts number for them? and Ill do more research on them and make a decision base on that....

thanks a bunch

Keas do a billet band servo aswell as a Kevlar lined band. basic upgrades include fitting extra clutches where possible, shift kit (transgo or superior), new solenoids and modifying the boost valve to up the line pressure a tiny bit. They are a good box and some parts can be interchanged from the RE4R03A range to add in strength

I wish for the life of me to know what is IN the RE401B.

It's not the RE401A, because that is the N/A box (so I am told), which I have also been told is "wildly weaker looking" than the GTT box.

I had a N/A box that had been built by MV, then got a new GTT box which I suppled, apparently very different.

It's also not the RE403A, cause that's different again. RE403A vs RE401B = ???????.

The 3's are a lot bigger internally, use a different valvebody and solenoid assemblies, clutches are slightly different with width/tooth count. Aswell as the wiring harnesses being different

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...